Войти:
Скачали: 0   Размер: 480 kb   Производитель: Honda Power Equipment  
Категория: Насосное оборудование
@name

Read and understand the Owner's Manual before operating the pump. Failure to do so could result in persona! injury or equipment damage. 1 CONTENTS 1. SAFETY INSTRUCTIONS................................................................................................................3 2. CAUTION LABEL LOCATION......................................................................................................4 3. COMPONENT IDENTIFICATION........................................................

Скачали: 0   Размер: 480 kb   Производитель: Honda Power Equipment  
Категория: Насосное оборудование
@name

Discard it if the insulator is cracked or chipped. Clean the spark plug with a wire brush if it is to be reused, 3. Measure the plug gap with a feeler gauge. The gap should be 0.7—0.8 mm 10.028—0.031 in). Correct as necessary by bending the side electrode. ^— 0.7 — 0.8 mm (0.028-0.031 ini 4. Thread the plug in by hand to prevent cross-threading. 5. Tighten a new spark plug 1/2 turn with the wrench to compress the washer. If you are reusing a plug, it should only take 1 /8 — 1 /4 turn after

Скачали: 0   Размер: 2 mb   Производитель: Bard  
Категория: Насосное оборудование
@name

Factory or field installed accessories are available to meet specific job requirements. Engineered Features Aluminum Finned Copper Coils: One Inch, Disposable Air Filters: Grooved tubing and enhanced louvered Are standard equipment. Optional one fin for maximum heat transfer and inch washable filters available and energy efficiency. filter racks permit the addition of 2" pleated filter. Factory or field installed. Twin Blowers: Move air quietly. Most models feature Solid State Electronic Heat Pu

Скачали: 0   Размер: 290 kb   Производитель: Trane  
Категория: Насосное оборудование
@name

Buildup of snow and ice can restrict airflow. As soon as possible after accumulation, clean snow from the area around the heat pump. To avoid overworking your unit, do not plant flowers or shrubbery right next to it. Also, make sure that nothing is stacked against the sides of the unit or draped over it. 22-5156-04-0804 (EN) 3 Keep your heat pump looking new for years. Clean the enamel finish of your heat pump with soap and water. For stubborn grease spots, use a household detergent. Do not use

Скачали: 0   Размер: 1 mb   Производитель: Honda Automobiles  
Категория: Насосное оборудование
@name

MAINTENANCE FUEL Fuel tank capacity: 0.66 US gal (2.5 f) Refuel in a well-ventilated area with the engine stopped. If the engine has been running, allow it to cool. Refer to page 41 for fuel recommendations and page 67 for information about oxygenated fuels. Never refuel the pump inside a building where gasoline fumes may reach flames or sparks. Keep gasoline lights, barbecues, electric appliances, away power from appliance tools, etc. pilot Spilled fuel is not only a fire hazard, Wipe up spills

Скачали: 0   Размер: 1 mb   Производитель: Honda Automobiles  
Категория: Насосное оборудование
@name

......................... 31 Safety Precautions. ............................. 31 MAINTENANCE SCHEDULE ....................... 32 FUEL. ......................................... 33 ENGINE MAINTENANCE .......................... 34 Engine Oil Change. ............................. 34 Engine Oil Recommendations. .................... 35 Air Cleaner Service ............................. 36 Spark Plug Service ............................. 38 Carburetor Adjustment. .......................... 40 Carburet

Скачали: 0   Размер: 714 kb   Производитель: Honda Power Equipment  
Категория: Насосное оборудование
@name

No part of this publication may be reproduced without written permission. This manual should be considered a permanent part of the pump and should remain with the pump if it is resold. Pay special attention to statements preceded by the following words: mzm Indicates a strong possibility of severe personal injury or loss of life if instructions are not followed. CAUTION: Indicates a possibility of personal injury or equipment damage if instructions are not followed. NOTE: Gives helpful informati

Скачали: 0   Размер: 1016 kb   Производитель: Honda Power Equipment  
Категория: Насосное оборудование
@name

4. Reinstall the air cleaner element and cover. AIR CLEANER ELEMENT AIR CLEANER COVER 3. 3. Recommended spark plug: BPRGES(NGK) W2OEPR-U(NlPPONDENS0) To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. 1. Remove the spark plug. The muffler becomes very hot during operation and remains hot for a while after stopping the engine. Be careful not to touch the muffler while it is hot. 2. Visually inspect the spark plug. Discard it if the insulator is cracked

Скачали: 0   Размер: 1 mb   Производитель: Trane  
Категория: Насосное оборудование
@name

Your serviceman should examine these areas of your WCY-G unit: . filters (for cleaning or replacement) . motors and drive system components . gaskets (for possible replacement) . safety controls (for mechanical cleaning) . electrical components and wiring (for possible replacement and connection tightness) . condensate drain (for cleaning) . unit duct connections (to see that they are physically sound and sealed to the unit casing) . unit mounting support (for structural integrity) . the unit (f

Скачали: 0   Размер: 1 mb   Производитель: Trane  
Категория: Насосное оборудование
@name

There is a bank of 8 dip switches, (See Figure 15), located at the upper right side of the board. The dip switches work in pairs to match the cooling/heat pump airflow (CFM/TON), Fan off-delay options, and electric heat airflow adjustment. The switches appear as shown in Figure 15. Page 15 t DIP SWITCHES (TYPICAL SETTINGS) ICM FAN CONTROL CFM SELECTION LIGHT DIP SWITCHES DEMAND DEFROST SYSTEM PIN IDENTIFICATION FRC_DFT DEFROST CONTROL The demand defrost control measures heat pump outdoor ambient





Категории