Оценок - 3, средний балл: 4.7 ( )

Инструкция по эксплуатации Ryobi, модель YN301PL

Производитель: Ryobi
Размер: 4.99 mb
Название файла: 5eb25abd-523c-4ee5-872c-e3300a96233e.pdf
Язык инструкции:enesfr
Перейти к скачиванию

Фрагмент инструкции

Turning the knob fully counterclockwise will completely stop the flow of air, as shown in the start up section of the quick reference label. NOTE: Always use the minimum amount of pressure necessary for your application. Using a higher pressure than needed will drain air from the tank more rapidly and cause the unit to cycle on more frequently. ■ When finished, always drain the tank and unplug the unit. Never leave the unit plugged in and/or running unattended. 13 - DRAINING THE TANK See Figure 12 - 13, page 18. To help prevent tank corrosion and keep moisture out of the air used, the air tank of the compressor should be drained daily. To drain: ■ Turn the air compressor off, as shown in the shut down section of the quick reference label. ■ Pull the ring on the safety valve to release until pressure gauge reads less than 20 psi, as shown in the shut down section of the quick reference label. ■ Release the ring. ■ Rotate drain valves counterclockwise to open, as shown in the shut down section of the quick reference label. ■ Tilt tank to drain moisture from tank into a suitable container. NOTE: Condensate is a polluting material and should be disposed of in compliance with local regulations. ■ If drain valve is clogged, release all air pressure, remove and clean valve, then reinstall. A WARNING: Unplug the air compressor and release all air from the tank before servicing. Failure to depressurize tank before attempting to remove valve can cause serious personal injury. ■ Rotate drain valve clockwise until tightly closed. CHECKING THE SAFETY VALVE See Figure 12, page 18. A DANGER: Do not attempt to tamper with the safety valve. Anything loosened from this device could fly up and hit you. Failure to heed this warning could result in death or serious personal injury. The safety valve will automatically release air if the air tank pressure exceeds the preset maximum. The valve should be checked before each day of use by pulling the ring by hand. ■ Turn the air compressor on and allow the tank to fill. The compressor will shut off when the pressure reaches the preset maximum. ■ Turn the air compressor off. ■ Pull the ring on the safety valve to release air for three to five seconds to allow pressurized air to escape. Release the ring. The safety release valve must reset and hold pressure before all compressed air is exhausted from the tank/pressure vessel. English OPERATION ■ Any continued loss of air after performing the above steps indicates a problem with the safety valve. Discontinue use and seek service before continued use of the air compressor. A WARNING: If air leaks after the ring has been released or if the valve is stuck and cannot be actuated by the ring, do not use the air compressor until the safety valve has been replaced. Use of the air compressor in this condition could result in serious personal injury. MAINTENANCE A WARNING: When servicing use only identical Ryobi® replacement parts. Use of any other parts may create a hazard or cause product damage. A WARNING: Always wear eye protection marked to comply with ANSI Z87.1 during maintenance. If operation is dusty, also wear a dust mask. A WARNING: Always release all pressure, disconnect from power supply, and allow unit to cool to the touch before cleaning or making repairs on the air compressor. GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. A WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommend using this product for extended work on these types of materials. However, if you do work with any of these materials, it is extremely important to clean the product using compressed air. LUBRICATION All of the bearings in this product are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required. NOTE: FIGURES (ILLUSTRATIONS) START ON PAGE 16 AFTER SPANISH LANGUAGE SECTION. 14 - English TROUBLESHOOTING PROBLEM CAUSE SOLUTION Compressor will not run Loss of power or overheating No electrical power Blown shop/house fuse Shop/house breaker open Amperage overload open Pressure switch bad Tank is full of air Check for proper use of extension cord Check to be sure unit is plugged in Check fuse/breaker Replace shop/house blown fuse Reset shop/house breaker,...

Эта инструкция также подходит к моделям:
Насосное оборудование - YN301PL1 (4.99 mb)

Напишите ваш отзыв об устройстве

Текст отзыва
Ваше имя:
Введите две цифры: