Войти:
Скачали: 0   Размер: 1 mb   Производитель: Delta  
Категория: Сантехника
@name

Install the spout. Rotate the spout escutcheon if necessary, so that the hole for the pull rod is at the rear. Tighten the mounting nut. Tighten the tensioning screws. Screw the connecting hoses into the spout tee. Slide the 3/8" compression nuts and ferrules over the ends of the hoses. Connect the hoses to the valve outlets. Use two wrenches so that the hoses do not twist or become loosened from the spout tee. Install the supply lines (not included). Install the drain. Turn on the water and che

Скачали: 0   Размер: 1 mb   Производитель: Axor  
Категория: Сантехника
@name

These strips must be removed before the spout is installed. Loosen the spout screw with a 2.5 mm Allen wrench.Pull the spout away from the escutcheon. Remove the adhesive strips. Reassemble the spout assembly so that the hole for the pull rod is at the rear of the spout. adhesive strips Installation Remove the valve mounting nuts from the valves. From below the mounting surface, push the valves up into the holes. Install the mounting nuts on the valves. Tighten the tensioning screws. Place the h

Скачали: 0   Размер: 1 mb   Производитель: Hans Grohe  
Категория: Сантехника
@name

incoming water pressure 145 PSI Recommended incoming water pressure 22 - 72 PSI Max. incoming hot water temp. 176°F* Recommended incoming hot water temp. 120° - 140°F* Max. flow rate -- lavatory faucets 2.2 gpm Max. flow rate -- bidet faucet 2.2 gpm The bidet faucet is not suitable for use on vertical spray bidets. This faucet may be used with a continuous flow water heater if the flow pressure is at least 20 PSI. For best results, Hansgrohe recommends that this faucet be installed by a licensed

Скачали: 0   Размер: 1 mb   Производитель: Honda Automobiles  
Категория: Сантехника
@name

Thisowner’smanual is considered a permanentpart of thewater pump and should remain with the water pump if resold. The information and specifications included in this publication were in effect at thetimeofapprovalforprinting. Honda Motor Co., Ltd. reserves the right, however,to discontinue or change specifications or design at any time without notice and without incurring any obligation whatever. No partofthispublicationmay be reproduced without written permission. Congratulationsonyourselection

Скачали: 0   Размер: 809 kb   Производитель: Bradley Brand Furniture  
Категория: Сантехника
@name@name@name

Separate parts from packaging and makesure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installationuntil you obtain the missing parts. Make sure that all water supply lines have been flushed and then completely turned off before beginning installation. Debris insupply lines can cause valves to malfunction. Hardware supplied by installer must be appropriate for wall construction. Wallanchors used must have a minimum pull-out rating

Скачали: 0   Размер: 417 kb   Производитель: Bradley Smoker  
Категория: Сантехника
@name

Main water supply to the unit should be ON at all times. This installation manual and parts list should be filed by the owner’s maintenance department. Installation Instructions WF2605, WF2608 Terrazzo WF2705, WF2708 Stainless Steel Classic Circular 36"/54" Washfountain with Foot Control 215-603 Rev. M; EN 06-915B © 2007 Bradley Corporation Page 1 of 28 4/6/2007 P.O. Box 309, Menomonee Falls, WI 53052-0309 TEL. 1-800-BRADLEY FAX 262-251-5817 Table of Contents Pre-Installation Information . . . .

Скачали: 0   Размер: 417 kb   Производитель: Bradley Smoker  
Категория: Сантехника
@name

Reassemble the operating rod as shown in Figure 12. Reinstall and adjust so that the foot valve is completely open when the foot lever is fully depressed. This prevents damage to the foot valve due to the absence of the override spring. 3. Turn supplies on and activate the sprayhead. Check piping installation for leaks. 4. Clean the sprayhead if necessary. See page 22 for sprayhead troubleshooting. Adjust the volume control valve, if necessary, to control the flow of water. Figure 12Figure 11 4/

Скачали: 0   Размер: 657 kb   Производитель: Honda Automobiles  
Категория: Сантехника
@name

Extended dry operation will destroy the pump seal. If the unit has been operated dry, stop the engine immediately and allow the pump to cool before adding priming water. PRIMING WATER 4. STARTING THE ENGINE 1. Turn the fuel valve ON. 2. Close the choke lever. NOTE: Do not use the choke if the engine is warm or the ambient temperature is high. ; FUEL VALVE CHQKE LEVER 3. Turn the engine switch to‘the ON position. 4. Move the throttle lever slightly to the left. THROTTLE LEVER 5. Pull the starter

Скачали: 0   Размер: 657 kb   Производитель: Honda Automobiles  
Категория: Сантехника
@name

All information in this publication is based on the latest product information available at the time of approval for printing. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. The illustrations in this book are based on the WB20X unless otherwise noted. No part of this publication may be reproduced without written permission. This manual should be considered a permanent part of the pump and should remain with the pump if it

Скачали: 0   Размер: 0 kb   Производитель: Honda Power Equipment  
Категория: Сантехника





Категории