Оценок - 3, средний балл: 3.3 ( )

Инструкция по эксплуатации Dixon Marking Tools, модель ZTL 312

Производитель: Dixon Marking Tools
Размер: 126.28 kb
Название файла: DIXO1992_USen_312_.pdf
Язык инструкции:en
Перейти к скачиванию

Фрагмент инструкции

DO NOT operate Bower without seat adjustment knobs properly tightened. 4. Close upper body and push retention latch (P/N 3934) over transaxle backing plate. REMOVING THE BODY 1. The 312 has a (2) piece polyethelene body. The upper body can be folded forward to expose the transaxle. In some cases, it nay be necessary to remove the upper body to service the transaxle. 2. To relieve upper body, remove two bolts (P/N 3080) from the front of upper body hinge located on the brake shaft (p/N 9283). Disconnect seat switch (P/N 4761) at plug-in. 3. Reverse above procedure to reinstall. ADJUSTMENT OF MOWER DECK DRIVE BELT 1. This mower deck drive belt is tensioned by a spring loaded engagement idler quadrant. 2. This system is designed to maintain the proper belt tension at all times. 3. Belt tension can be adjusted by moving the engaging rod (P/N 7013) into the outside hole of engagement handle (P/N 7020). 4. After belt tension is adjusted, check to assure that the mower blade will not turn freely when the engaging rod is in the "OFF" positon. 5. If the mower blade turns freely, adjust the blade brake by loosening nut (P/N 3205) at the end of the brake rod (P/N 2988). 6. After adjustment is achieved, perform the safety checks listed below. Page 1 of 7 REMOVING THE MOWER BLADE Secure blade (P/N 2483) from turning. Remove blade bolt from center of blade (P/N 3268), and blade washer (P/N 6260) then remove blade (P/N 2483). To reinstall, reverse above procedure. WARNING: Sharp edges on blade can cause Injury! Caution should be exercised when service is required on blade. REMOVING THE MOWER DECK 1. Loosen belt keeper (P/N 7026 & 7027) located under the engine, by loosening two rear engine mounting bolts, allowing the deck drive belt to come free of the rear pulley. 2. Disconnect the wiring loom at the deck safety switch (P/N 4242). 3. Remove the two clevis pins (P/N 3072) from the two rear L-rods (P/N 1355) and slide from slots. 4. Remove clevis pin (P/N 3072) from L-rod attached to lift handle and slide from slot. 5. Remove clevis pin (P/N 3072) from front deck hanger shaft (P/N 1332), located at front of mower deck on slide plates welded at battery box, and remove. 6. Lift front of mower chassis clear of deck. Roll chassis free of the deck. 7. To Install, reverse the above procedure. MOWER BLADE OPERATION To engage mower blades, turn engagement lever on floor slowly to the "ON" position. To disengage mower blades, turn lever slowly to the "OFF" position. "IMPORTANT" - PERFORM SAFETY CHECKS AFTER MAKING ANY REPAIRS OR ADJUSTMENTS 1. After reassembly, while seated on mower, attempt to start engine with mower deck engaged. Engine should not start. If engine does start, return the mower to an Authorized Dixon Dealer for adjustment or repair. 2. Disengage mower deck and start engine. With the operator in the normal seated position, engage mower deck and remove weight from seat. The engine should stop. If the engine doesn't stop when operator rises from the seat, return the mower to an Authorized Dixon Dealer for adjustment or repair. 3. Engage, then disengage, mower blade in each cutting height. Insure that blade disengages and comes to a stop within (5) seconds In each height position. If blade does not disengage properly, contact your Authorized Dixon Dealer. PARKING BRAKE ADJUSTMENT Remove the body as described above. Tighten nut on brake rod (P/N 2533) located in front of the transaxle on each side, just enough to prevent brake from slipping when engaged. CAUTION: Over tightening may cause premature wear on the brake band (P/N 5085). Page 2 of 7 Revised 1/92 (P/N 8114) “чзтео 30ÛSK 19*0/ 3796' 3007* -0J73 w/GRIP ■3204 г А ( 2-1 ■10ZQ '3205 3093] ■0372 '3033, '^307* ■3020 37« 4.- зооз/ f30S3 ■7027 3033- 3224-3Ô70-597636777594- 2*65 í TJR£ )• ■33*0 3077' 2 Transaxle Assembly -, 3i2 Wiring Assembly TO DECK SWITCH...

Напишите ваш отзыв об устройстве

Текст отзыва
Ваше имя:
Введите две цифры: