Оценок - 4, средний балл: 4.5 ( )

Инструкция по эксплуатации Yard Machines, модель YM290

Производитель: Yard Machines
Размер: 2.32 mb
Название файла: 80959eea-cca6-0004-7101-a77cab562226.pdf
Язык инструкции:enesfr
Перейти к скачиванию

Фрагмент инструкции

Comply with times listed in local ordinances. Usual recommendations are 9:00 am to 5:00 pm, Monday through Saturday. • To reduce noise levels, limit the number of pieces of equipment used at any one time. • To reduce noise levels, operate power blowers at the lowest possible speed to do the job. • Check your equipment before operation, especially the muffler, air intakes and air filters. • Use rakes and brooms to loosen debris before blowing. • In dusty conditions, slightly dampen surfaces or use a mister attachment when water is available. • Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as screens, patios, grills, porches, and gardens. Fig. 5 Fig. 6 MAINTENANCE AND REPAIR INSTRUCTIONS FREQUENCY MAINTENANCE REQUIRED REFER TO Before starting engine Fill fuel tank with fresh fuel Page 8 Every 10 hours Clean and re-oil air filter Page 11 Every 25 hours Check spark plug condition and gap Page 12 MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up. NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures take your unit to any non-road engine repair establishment, individual or authorized service dealer. To prevent serious WARNING: injury, never perform maintenance or repairs with unit running. Always service and repair a cool unit. Disconnect the spark plug wire to ensure that the unit cannot start. AIR FILTER MAINTENANCE NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by any non-road engine repair establishment, individual or authorized service dealer. In order to assure peak performance of your engine, inspection of the engine exhaust port may be necessary after 50 hours of operation. If you notice lost RPM, poor performance or general lack of acceleration, this service may be required. If you feel your engine is in need of this inspection, refer service to any non-road engine repair establishment, individual or authorized service dealer for repair. DO NOT attempt to perform this process yourself as engine damage may result from contaminants involved in the cleaning process for the port. To avoid serious WARNING: personal injury, always turn your unit off and allow it to cool before you clean or service it. Clean and re-oil the air filter every 10 hours of operation. It is an important item to maintain. Failure to maintain your air filter properly can result in poor performance or can cause permanent damage to your engine. 1. Remove the carburetor/air filter cover by pushing on the tab, located to the right of the cover (Fig. 7). 2. Swing the air filter cover open. It will swing on the hinges to the left of the cover (Fig. 8). 3. Remove the air filter (Fig. 8). 4. Wash the filter in detergent and water. Rinse the filter thoroughly and allow it to dry (Fig. 9). 5. Apply enough clean SAE 30 motor oil to lightly coat the filter (Fig. 10). 6. Squeeze the filter to spread and remove excess oil (Fig. 11). 7. Reinstall the filter and close the air filter cover (Fig. 7). NOTE: If the unit is operated without the air filter, you will VOID the warranty. Fig. 7 Air Filter Cover Tab Air Filter Tab Fig. 8 MAINTENANCE AND REPAIR INSTRUCTIONS Fig. 9 Fig. 10Fig. 11 REPLACING THE SPARK PLUG Use a Champion RDJ7Y spark plug, or equivalent. The correct air gap is 0.020 inch (0.5 mm). Remove the plug after every 25 hours of operation and check its condition. 1. Stop the engine and allow it to cool. Grasp the plug wire firmly and pull it from the spark plug. 2. Clean around the spark plug. Remove the spark plug from the cylinder head by turning a 5/8-inch socket counterclockwise. 3. Replace a cracked, fouled or dirty spark plug. Set the air gap at 0.020 in. (0.5 mm) using a feeler gauge (Fig. 12). Do not sand blast,WARNING: scrape or clean electrodes. Grit in the engine could damage the cylinder. 4. Install a correctly-gapped spark plug in the cylinder head. Tighten by turning the 5/8-inch socket clockwise until snug. If using a torque wrench torque to: 110-120 in.•lb. (12.3-13.5 N•m) Do not over tighten. CLEANING THE UNIT To avoid serious WARNING: personal injury, always turn your unit off and allow it to cool before you clean or service it. Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing or handle. Wipe off any moisture with a soft cloth. 0.020 in. (0.5 mm) Fig. 12 STORAGE • Never store a fueled unit where fumes may reach anopen flame or spark. • Allow the engine to cool before storing. • Store the unit locked up to prevent unauthorized useor damage. • Store the unit in a dry, well-ventilated area. • Store the unit out of the reach of children. LONG TERM STORAGE If you plan on s...

Напишите ваш отзыв об устройстве

Текст отзыва
Ваше имя:
Введите две цифры: