Оценок - 3, средний балл: 4 ( )

Инструкция по эксплуатации NuTone, модель VSM4RK

Производитель: NuTone
Размер: 477.01 kb
Название файла: ca1a9a0e-7890-46a5-b894-c2cef0f0659c.pdf
Язык инструкции:enfr
Перейти к скачиванию

Фрагмент инструкции

• Once the handset is lifted, audio communication is established between the handset and the monitor location. Priority Call Button This button is used together with the Talk Button and Monitor Button to disable the microphone at the camera. Normal use would be to cut out unwanted outside noise during conversation heard at the main unit. Press the “Talk Button” and the “Monitor Button”. • Lift the optional handset (VSA4S) to initiate all three calling devices • Press the “Priority Call Button”. The camera microphone is disabled so no audio communication will be heard while the “Priority Call Button” is active. Audio and video remain normal at the monitor and the handset retains normal audio communication. Talk Button This button is used for all audio communications. If this button is activated (red Talk LED remains on) it will remain on indefinitely. • If the optional handset is lifted, audio communication is established between the handset and the monitor. To turn off the “Talk and the Talk LED” , Press the “Talk Button” and any communication is terminated. 4 Optional Handset Operation (VSA4S) Lift handset and depress “Call Button” on handset. • Monitor must have “Talk Button” activated for audio communication to be established between handset and monitor. Camera Operation Press “Call Button” on camera. • Video turns on at monitor. • “Talk Button” at monitor must be pressed to initiate audio between camera and monitor. • If handset is lifted, audio communication between the camera and handset is established. Ending the Door Call Once audio and video communication is established between the camera and the monitor, press the “Monitor and Talk Buttons” so that each red LED turns off. Audio and video communications will be terminated. Video Timeout The video will deactivate the camera and turn off the display after 60 seconds, unless manually turned off by pressing the “Monitor Button”. Resetting the Monitor This is performed by turning the On / Off / Standby switch to the leftmost position to power down the product. Wait a minimum of 30 seconds prior to moving the On / Off switch to the “On” position to power the monitor. Camera Volume Adjustment The VSC4R and VSC4S door cameras are provided with a volume level adjustment set screw. The adjustment has been pre-set at the factory to provide the optimal volume level at the door camera. The volume level can be adjusted if your specific application requires the level to be either increased or decreased. Insert a jeweler’s screwdriver into the small hole that is shown in the camera illustration. Rotate the small set screw to adjust the volume level. Important: Do not use excessive force to rotate the screw. Damage could occur to the camera, and loss of audio may result. Use extreme caution when making the adjustment. Do not use a screwdriver that is too big for the application. VSC4S Volume Adjustment VSC4R Volume Adjustment VSC4S Lens Adjustment VSC4R Lens Adjustment Camera Lens Manual Adjustment The VSC4R and VSC4S door cameras are provided with a manual camera lens adjustment. The adjustment can be used to fine tune the angle of the camera lens to compensate for installations that are not directly in line to the viewing area. The adjustment is located on the back of the camera, as shown in the camera illustration. Move the adjustment control upward to lower the camera lens. Move the adjustment control downward to raise the camera lens. Adjust the camera lens position to provide the best viewing area for your installation. The VSC4R camera will also adjust the lens to the sides. 5 FCC Information Part 15 Rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Warning – This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change o...

Эта инструкция также подходит к моделям:
Автоответчики - VSM4SK (477.01 kb)

Напишите ваш отзыв об устройстве

Текст отзыва
Ваше имя:
Введите две цифры: