Войти:
Оценок - 2, средний балл: 4.5 ( )

Инструкция по эксплуатации Liquid Image, модель Scuba Series Wide Angle 323

Производитель: Liquid Image
Размер: 2.31 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


The CAMERA MASK will return to the still image mode (RED LED). 5. In case the battery needs to be replaced or the battery runs out, the date setting data will be maintained for 24 hours 3.4 Camera Lock The RUBBER BUTTON PLUG keeps the CAMERA MASK from turning on during transport or non diving activities. To unlock the POWER/MODE button, pull the Rubber Button Plug out from under the POWER/MODE button and rotate it upwards I or downwards. 4.0 RECORDING PICTURES AND VIDEO CAUTION: Read and perform the 4 Part CAMERA TEST described in this manual prior to using in the water! NOTE: The CAMERA MASK has 2 modes and pressing the POWER/MODE button ENG-9 cycles through the modes in the following order: Video and Still Image. To advance to the next mode, press the POWER/MODE button one time. The camera will remain on and ready to use for 180 seconds, after which the CAMERA MASK will turn off automatically. If you press and hold the POWER/MODE for more than 1 second, the camera will also turn off. 4.1 Video Mode-BLUE LIGHT № 1. Press the POWER/MODE button for at least 1 second. The camera turns on. The camera will power up in VIDEO mode. Note: The BLUE MODE LIGHT INDICATOR is on and the CAMERA MASK is now in the VIDEO MODE READY mode and set to take videos. The LCD screen displays the movie camera icon. 2. Press the SHUTTER/SELECT button once. Recording begins. Note: The BLUE MODE LIGHT INDICATOR is blinking. The light will continue to blink until the camera stops recording. 3. To stop recording, press the SHUTTER/SELECT button again, 4.2 Still Image Mode-RED LIGHT Q 1. Press the POWER/MODE button for at least 1 second. The camera turns on. 2. Press the button the POWER/MODE button again for less than a second to change to STILL IMAGE mode. Note: The RED MODE LIGHT INDICATOR is on and the CAMERA is now in STILL IMAGE READY mode and set to take pictures. The LCD screen displays the camera icon. 3. Press the SHUTTER/SELECT button once. A still image is captured. NOTE: To capture the sharpest in focus images, it is important that the distance between the camera and the subject is at least 1.2m (47.25 inches). 4.3 Power Off 1. Press the POWER/MODE button for more than 1 second to turn the camera off. NOTE: If either the POWER/MODE or the SHUTTER/SELECT button has not been used in 180 seconds, the CAMERA MASK will turn off automatically. ENG-10 5.0 TRANSFERRING STILL IMAGES AND VIDEO TO A COMPUTER CAUTION: ALWAYS FOLLOW THE CARE AND MAINTENANCE INSTRUCTIONS FOR RINSING IN FRESH WATER AND DRYING THE CAMERA MASK PRIOR TO OPENING THE MEMORY COMPARTMENT. The CAMERA MASK has two ways to transfer your image and video flies to a computer. The CAMERA MASK comes with a USB cable (RCA/USB CABLE) to connect your CAMERA MASK directly to a computer. You may also choose to purchase and use a commercially sold Micro SD/SDHC Card to store and transfer images and videos that were taken with the CAMERA MASK. The computer does not require software to access the files stored on the CAMERA MASK’S Micro SD/SDHC card.The CAMERA MASK will act as an external hard drive when the USB cable connects the camera to a computer 5.1 Opening Memory Compartment 1. Make sure the CAMERA MASK is thoroughly clean and dry. Follow the CARE AND MAINTENANCE instructions. 2. Open the MEMORY COMPARTMENT. 3. Locate and remove the rubber DRIP GUARD. Make sure the DRIP GUARD is clean and dry before proceeding. CAUTION: Do not lose this part. The DRIP GUARD is part of the water proofing system. 5.2 Connecting and Transferring Files 1. Choose a method to transfer files: USB or Micro SD/SDHC Card. USB TRANSFER Plug the USB cable into the USB connection port on the computer and then into the USB Port on the CAMERA MASK. Press the POWER/MODE to turn on the CAMERA MASK. NOTE: The USB cable will be able to access the files stored on the Micro SD/SDHC Card. MICRO SD/SDHC CARD TRANSFER Press down on the Micro SD or SDHC Card gently. The card will pop up for removal. Carefully remove the card and insert it into the Micro SD card adapter that comes with the Micro SD/SDHC Card and then insert the card into your computer's SD Card Slot as directed by the manufacturer. ENG-11 * Make sure your computer's SD Card Slot can handle High Capacity SDHC cards as they are different than standard SD cards. CAUTION: Never insert a wet Micro SD/SDHC Card into a card adapter or into a Computer. 2. The connection screen opens on your computer monitor automatically. Choose the option: OPEN FOLDER TO VIEW FILES. NOTE: If the screen does not automatically open, look for a new hard drive icon on the computer next to your other hard drive icons. Click on the icon to view your image and video files. 3. The image and video files will appear in a folder. 4. Copy the files to a folder on your computer (For example: My Pictures\Hawaii). Alternatively, you may copy the entire folder to your computer. 5. If you wish to delete the data from the CAMERA MASK'S Micro S...

Эта инструкция также подходит к моделям:
Видеоочки - Scuba Series Wide Angle 322 (2.31 mb)
Видеоочки - Scuba Series Wide Angle UDCM 322 (2.31 mb)
Видеоочки - Scuba Series Wide Angle UDCM 323 (2.31 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории