- so it works particularly well where space is at a premium or where a lighter scale presence is desired. The raised leg enhances the lightness of scale and provides easy access for cleaners. CITI is finished beautifully in Italian Leather or Leather/Mock Leather combinations. Cushions are sewn with doubleneedle-stitched seams and sits high and firm, making it extremely appropriate as reception area or office seating. DESCRIPTION DIMENSIONS SEAT HEIGHT W D H IN IN IN IN mm mm mm mm 78
In addition, Classic Collection Lift Chairs feature patented, quiet and smooth operation and stylish designs to add to any home décor. COLLECTION 1-800-800-8586 (U.S.) 1-888-570-1113 (Canada) Prides Mobility Products Corp. Pride Lift Chats ¿(¿^xßerieaee l/e Qhhvt(-/y # *1(¿SS¿C (^COLLECTION CLASSIC COLLECTION MODELS CL-10 CL-152 CL-20 CL-3Q2 2-Position 3-Position 2-Position 3-Position Medium Medium Medium Medium Button-back Design Button-back Design Sewn Pillow-back Design Chaise Lo
Evitar lesiones graves o la muerte debido a caidas: El nino debe quedar asegurado en la silla alta en todo momento con el sistema de sujecion, ya sea, en la posicion reclinada o vertical. Ajustar los cinturones de sujecion al tamano de su hijo. La bandeja no esta disenada para sujetar al nino en la silla. WARNING AVERTISSEMENT ADVERTENCIA Secure Your Child Comment installer l'enfant Asegurar al bebe 1 • Place your child in the seat. Position the crotch belt between your child’s legs. • Fasten bo
Requires three “AA” batteries (included). Adult assembly is required. Tool required for assembly: Phillips screwdriver (not included). L4889 Please keep this instruction sheet for future reference, as it contains important information. Requires three “AA” batteries (included). Adult assembly is required. Tool required for assembly: Phillips screwdriver (not included). Parts Consumer Information Seat Bottom Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the sc
Tighten the screw. •Repeat this procedure to fasten the other frame back leg to the other side of the back base. Hint: The #10 x 2,2 cm black screws may have been assembled to the screw retainers. Frame Decorated Side Frame Back Legs Back Base Screw Retainers 8 •While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown. Seat Height Adjusters Position Press Lever 9 •Fit the seat assembly between the two frames. •Insert the seat bottom tubes
Prevent serious injury or death from falls or sliding out: • The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. • It is recommended that only children capable of sitting upright unassisted use the high chair in the upright position. • Always keep child in view while in the high chair. • Never leave child unattended. • Do not use the high chair unless all components are correctly fitted and adjusted. Prevent
An operator should not operate on a slope until he is thoroughly familiar with the equipment. Do not operate on slopes greater than 15 degrees. Refer to Figure 2-1, page 7, when determining the degree of slope to be mowed. IMPORTANT: The Hustler ATZ only, is capable of operating on slopes of 15 degrees or more (maximum 25 degrees). Do not operate the Hustler ATZ on slopes greater than 25 degrees. Refer to Figure 2-1, page 7 when determining the degree of slope to be mowed. It is strongly recomme
Do not overfill battery. Electrolyte may overflow and damage paint, wiring or structure. When cleaning the battery, use soap and water. Be careful not to get soap and water into the battery. Use soda mixed in water to clean corrosion off the terminals. Avoid crushing Do not jump if machine tips Use seat belt Seat belt must be fastened while operating this machine. Failure to use seat belt will result in serious injury in the event of a roll over. Keep engine and pump compart-ment(s) clean (espec
C. Deck clutch switch (Fig. 3-1) — this switch engages the deck. Pull the switch up to engage and push switch down to disengage the clutch. IMPORTANT: Never engage clutch with engine running at high rpm or when the deck is under load. Clutch, belts or deck could be damaged. D. Ignition switch (Fig. 3-1) – a three position switch: off, run, and start. With key inserted, rotate it clockwise to START position; release key when engine starts, and switch will automatically return to the RUN position.
. Own? 2. . Rent? BU Your marital status: 1. . Married 2. . Single CL Education (Please check which category applies): 1. . High School 3. . Completed College 2. . Some College 4. . Graduate School CM Including yourself, what is the total number of people living in your household? (Examples: 01, 02, 03, 04...) CN NOT including yourself, what are the AGES of the other people living in your household? Age (in years) Male: Female: CO Which best describes your family income? 1. . Under $15,000 5. .