Оценок - 5, средний балл: 3.4 ( )

Инструкция по эксплуатации Bush Hog, модель X7502831700

Производитель: Bush Hog
Размер: 1.49 mb
Название файла:
Язык инструкции:
Перейти к скачиванию

Фрагмент инструкции

2 - 5 x 8 mm screws, 2 - 5 mm nuts, 2 - 5 mm lock- washers, (bracket to shield). 2 - 5 mm nuts, 2 - 5 mm lockwashers (Bracket to Gear Housing) Assembly (continued) 1. If installed remove nylon line head, adapter plate, shield plate, and plastic shield: a. Align locking hole in adapter plate with notch in edge of gear housing and insert head locking tool (A). b. Remove line head (B) by turning it clockwise until head is completely off of shaft. c. Remove locking tool. d. Removethreescrewsholdingshieldplate(E)andplasticshield(C)togear housing. e. Retain line head (B), adapter plate (D), shield plate, and plastic shield (C). A B C C E D 2. Loosely attach bracket (I) to shield (J) and attach shield to bottom of gear housing (F) with hardware provided. 3. Tighten all shield hardware. J I F Assembly (continued) Install Blade Tools Required: 4 mm hex key wrench (locking tool), 17 mm wrench, Pliers Parts Required: Adapter plate w/25 mm diameter pilot, lower blade mounting plate, 10 mm hex nut w/L.H. thread, 2 mm x 25 mm cotter pin, blade w/25 mm arbor diameter. The unit should now be completely assembled and ready for use with a blade. IMPORTANT! Discard blades that are bent, warped, cracked, broken or damaged in any way. D A K G L H D K H G L A 1. Install adapter plate (D) on splined PTO shaft, pilot side down. Blade installation requires Upper Plate (D) with 25 mm pilot. 2. Install Blade (K) on adapter plate pilot. Blades must be installed so that rotation arrow on blade matches rotation of unit: teeth toward direction of rotation (See debris shield decal). Secure blade with Lower Plate (H), and 10 mm L.H. nut (G). Turn nut counter-clockwise on PTO shaft to tighten. 3. Align hole in adapter plate with notch in gear housing, and insert Locking Tool (A) to prevent splined shaft from turning. Arrow on gear housing points to notch. Tighten 10 mm nut securely. 4. Insert Cotter Pin (L) in hole in PTO shaft, and bend pin legs around shaft counterclockwise to retain 10 mm nut. IMPORTANT Never reuse a cotter pin - install a new cotter pin each time a blade is installed or replaced. 5. Remove locking tool. Use a sharp blade. A dull blade is more likely to snag and thrust. Mixing Fuel WARNING! Alternative fuels, such as E15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa requirements are NOT approved for use in Shindaiwa gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components. Fuel Requirements Gasoline -Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. Hybrid 4TM Mixture ...

Эта инструкция также подходит к моделям:
Садовые инструменты - C344 (1.49 mb)
Садовые инструменты - C344 (1.49 mb)
Садовые инструменты - C344 (1.49 mb)
Садовые инструменты - C344 (1.49 mb)

Напишите ваш отзыв об устройстве

Текст отзыва
Ваше имя:
Введите две цифры: