К этому устройству также есть другие инструкции:
Compatible devices can connect to the YWA-10 • Check that the Wireless LAN router (base unit) through a USB connector instead of a DC OUT jack. can connect to the Internet. Refer to the website below for a list of compatible © 2012 Yamaha Corporation Printed in China devices. To assure the finest performance, please read this AV Receiver Connecting to the base unit manual carefully. Keep it in a safe place for future reference. Package contents • When the Wireless LAN router (base unit) has a WPS button ^ Carry out the procedures in “Step 2-A Connecting to the base unit (using WPS)” to Check that the following accessories are supplied with connect to the base unit. the product. • When the Wireless LAN router (base unit) does not have a WPS button Wireless Network ^ Carry out the procedures in “Step 2-B Connecting to the base unit (manual Adapter (this unit) YWA-10 configuration)” to connect to the base unit. . If connecting using “(using WPS)” does not succeed, refer to “(manual configuration)” and LAN cable configure the connection. Features Setup procedure The firmware of this unit may be updated at times for improvement. Please refer to the following website for information on firmware updates. Internet connection Modem Wireless LAN router (base unit) Connecting to an AV product The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance. The Wi-Fi Protected Setup Mark is a mark of the Wi-Fi Alliance. Part names Owner’s Manual (this manual) USB power cable Step 1 Checking the base unit Upper surface of product Rear a Check that the wireless LAN router (base unit) can connect to the d ef Internet without difficulty. Internet Internet connectivity connection Side router (base unit) g a POWER indicator b WPS indicator Notes c WIRELESS indicator • If you do not currently have an Internet subscription, please obtain one. d Power connector • A wireless LAN router is required to set up a connection using this e LAN1 port, LAN2 port procedure. Please obtain a wireless LAN router if you do not have one f WPS button available. g Reset button b Check whether the wireless LAN router (base unit) is WPS compatible. Check the owner's manual and other documentation supplied with the wireless LAN router. Things to check before setup • If you do not already have an Internet connection, please apply for one Note before setting up this unit. WPS (Wi-Fi Protected Setup) is a function that uses a button to configure • Do not connect the USB power cable to a USB hub. connections and security on wireless LAN devices. *Some Wi-Fi devices have “WPS” written on them. c ab Wireless LAN Modem Computer Step 2-A Connecting to the base unit (using WPS) Notes • This explanation details the procedure for connecting using the WPS function. When using a base unit that is not equipped with a WPS function, refer to “Step 2-B Connecting to the base unit (manual configuration)” at right. • You will need to change the IP address of this unit if you are using more than one YWA-10 at the same time. Refer to “Troubleshooting” on the reverse page for more details. 1. Supply power to the YWA-10 a Turn on the power of the AV product that you wish to connect this unit to. b Use the supplied USB power cable to connect the power connector on this unit to the DC OUT jack on the AV product. The indicator on the front panel of this unit lights. Wait for approximately one minute after the indicator lights and then carry out the following procedure. Note If the AV product is not equipped with a DC OUT jack, connect to the USB connector on the front panel. Rear Panel AV Receiver 2. Connect the base unit a Press the WPS button on the wireless LAN router (base unit). Refer to the owner’s manual of the wireless LAN router (base unit) for information on how to use the WPS button. b Press and hold the WPS button on the rear of this unit for more than 5 seconds and release it. The WPS indicator on the front panel lights. Press and hold for more than 5 seconds. c Wait until the WPS indicator turns off (this will take two minutes at most). Note If the WPS indicator blinks, carry out procedure 2 again, starting at number a. This completes connection with the base unit. Proceed to “Step 3 Connecting to an AV product”. Step 2-B Connecting to the base unit (manual configuration) Notes • When making a manual connection to the base unit, or when you are unable to connect using the procedure described in “Step 2-A Connecting to the base unit (using WPS)” at left, refer to the explanation below. • If the PC you are using to configure this unit is connected to the wireless LAN, turn the PC’s wireless LAN function off. • You will need to change the IP address of this unit if you are using more than one YWA-10 at the same time. Refer to “Troubleshooting” on the reverse page for more details. 1. Check the network that you are attempting to connect to. You will need the setting information from the wireless LAN router (base unit) w...