Оценок - 3, средний балл: 5 ( )

Инструкция по эксплуатации Casio, модель XJ-H1650

Производитель: Casio
Размер: 1.03 mb
Название файла:
Язык инструкции:en
Фото и характеристики  Casio  XJ-H1650
Перейти к скачиванию

Фрагмент инструкции

Pointers can be used during a presentation to indicate or highlight a specific part of the image. Note Depending on the pointer style you are using, the pointer may not display properly when you are using keystone correction. If this happens, use the [KEYSTONE +] and [KEYSTONE –] keys to change the keystone correction value to zero. To display a pointer in the image 1. Press the [POINTER] key. • This will cause a pointer to appear in the image. • You also can use the setup menu to specify the pointer type that appears first when you press the [POINTER] key. For details, see “Pointer” under “Option Settings 2 Main Menu” on page 36. 2. Use the cursor keys to move the pointer to the location you want. • Holding down a cursor key moves the cursor at high speed. 3. To modify the pointer as described below, press the [STYLE] key. For this pointer type: Pressing [STYLE] will change it like this: • • • • • • • • • • • • Toggle between flashing and not flashing To select the pointer type 1. Press the [POINTER] key to display the pointer. 2. Keep pressing the [POINTER] key until the pointer you want is displayed. • Each press of the [POINTER] key cycles through the available pointer types. To clear the pointer from the image Press the [ESC] key. 16 Changing the aspect ratio of the projected image Press the [ASPECT] key to cycle through the aspect ratio settings for the projected image. Available settings are as shown below. For details about the meaning of each setting, see the “Aspect Ratio” setting under “Screen Settings Main Menu” on page 32. Input Source Pressing [ASPECT] will toggle between these settings: Video, S-video, Component, HDMI (DTV) Normal • 16:9 RGB, HDMI (PC) Normal • Full Note • When the input source is a component or an HDMI (DTV) signal with an aspect ratio of 16:9, the aspect ratio is fixed at 16:9. In this case, pressing the [ASPECT] key will not change the aspect ratio setting. • For details about how the aspect ratio setting affects the projected image, see “Aspect Ratio Setting and Projection Image” (page 50). • You also can change the aspect ratio setting using the setup menu. For details, see “Aspect Ratio” under “Screen Settings Main Menu” on page 32. Important! Note that enlarging or reducing the size of an image using the [ASPECT] key for commercial purposes or public presentation may infringe on the legally protected copyright of the copyright holder of the original material. 17 Adjusting the Volume Level You can use the remote controller keys to adjust the volume level of the audio that is output from the projector’s speaker. To adjust the volume level 1. Press the [VOLUME] key. • This causes the [Volume] screen to appear on the projected image. 2. Press the [..] key to increase the volume, or the [..] key to lower the volume. 3. After the setting is the way you want, press the [ESC] key. • This causes the [Volume] screen to disappear. Note You also can use the setup menu to adjust the volume level. For details, see “Volume Adjustment Main Menu” on page 31. To mute the audio 1. Press the [VOLUME] key. 2. Press the [ENTER] key. • This stops output from the speaker. 3. To restore the audio, press the [VOLUME] key again. 18 Eco Mode (Power Saving, Low Noise) The following three Eco Mode settings are available to specify whether priority should be given to low-power, low-noise operation or to projection brightness. On (Auto) : A brightness sensor on the top of the projector senses surrounding light, and automatically adjusts projection brightness and color accordingly. Brightness is reduced for darker surroundings, which saves power and reduces operation noise. On (Manual): Enables manual adjustment to balance the needs of low-power, quiet operation and projection brightness. Off : Give top priority to projection brightness. Important! • While “On (Auto)” is selected as the Eco Mode setting, make sure that the brightness sensor on the top of the projector is not blocked by anything. • The local environment and setup conditions affect the brightness sensor, so operation when “On (Auto)” is selected for the Eco Mode depends on these factors. To select the Eco Mode 1. Press the [ECO] key. • This causes “Eco Mode” window to appear on the projection screen. 2. Use the [..] and [..] keys to select the setting you want. • If you select “On (Manual)” here, go to step 3. If you select another setting, jump to step 4. 3. Perform the following steps to adjust the “Eco Level” (the balance between low-power, quiet operation and projection brightness). 1 Press the [..] key to move the highlighting to the Eco Level. 2 Use the [..] and [..] keys to adjust the Eco Level to the setting you want. Fewer marks gives higher priority to projection brightness. A greater number gives high priority to low-power, quiet operation. 4. To hide the window, press the [ESC] key. 19 Important! • The Eco Mode setting automatically changes to “Off” whenever the projector is in the 3D input mode (“3D Input Mode”, page 11) or...

Эта инструкция также подходит к моделям:
Электронные книги - XJ-H1600 (1.03 mb)
Электронные книги - XJ-ST145 (1.03 mb)
Электронные книги - XJ-ST155 (1.03 mb)

Напишите ваш отзыв об устройстве

Текст отзыва
Ваше имя:
Введите две цифры: