Оценок - 3, средний балл: 4.3 ( )

Инструкция по эксплуатации Dual, модель XDM7615

Производитель: Dual
Размер: 575.59 kb
Название файла: ced663d9-8d7a-4d30-bc3d-de9ca668b4b4.pdf
Язык инструкции:en
Перейти к скачиванию

Фрагмент инструкции

Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove trim ring from unit, • Remove 2 transit screws located on top of the unit. • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • Install mounting sleeve into opening, bending tabs to secure. • Connect wiring harness and antenna. Consult a qualified technician if you are unsure. • Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately). • Test for correct operation and slide into mounting sleeve to secure. • Snap trim ring into place. XDM7615 INSTALLATION Preparation XDM7615 INSTALLATION Wiring Diagram BLUE Subwoofer Preamp Output BLACK Front Preamp Output Steering Wheel Interface Input PAC SWI-PS required Antenna Connector FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XDM7615 uses one 10 amp ATM fuse located beside the wiring connector. XDM7615 OPERATION Control Locations -Receiver 268931011141415161718192021137125 1234567891011 Tune/Track Up Mode/Search Audio/Setup EQ Mute Preset 1/Repeat Preset 4/Play/Pause Preset 2/Random Preset 5/Folder Down Preset 3/Intro Preset 6/Folder Up 14151617181920211213 Eject Auxiliary Input Open AS/PS/Enter Band Scan Display Reset Power Tune/Track Down XDM7615 OPERATION Control Locations -Remote 124319171820211656789131514101211 1234567891011 Mode/Search Volume Up Power Audio/Setup Tune/Track Up Volume Down AS/PS/Enter Preset 2/Random Preset 3/Intro Preset 6/Folder Up EQ 12131415161718192021 Scan Loudness Open Display Mute Preset 5/Folder Down Preset 4/Play/Pause Preset 1/Repeat Band Tune/Track Down XDM7615 OPERATION General Operation Front Panel Removal Power On/Off Mode Auxiliary Input Steering Wheel Interface Input Volume Programmable Turn-On Volume Preset EQ Curves Display Reset With the unit off, press EJECT to allow the front panel to slide down. Gently squeeze the release tab located on the bottom center underside and pull front panel down and away from unit to remove. To install, insert left side first, then push right side to secure. Press POWER or any other button (except EJECT or OPEN) to turn the unit on. Press POWER to turn the unit off. Press MODE to select between AM/FM, CD player and auxiliary input. Modes of operation are shown in the display. NOTE: CD mode will not appear unless a CD is inserted. Insert a 3.5mm connector into the front panel AUX port. Connect the other end of the 3.5mm connector to the headphone output of an audio device, MP3 player, etc. Press MODE to select AUX mode. The steering wheel interface input located on the back of the head unit allows connection to the Pacific Accessory Corporation (PAC) SWI-PS interface module (sold separately). Visit for details. To configure steering wheel controls, follow the instructions provided with the PAC SWI-PS interface module. After installing the interface module, insert the module's 3.5mm jack into the port on the back of the head unit. Adjust volume using rotary encoder (00-46). Press and hold POWER for 2 seconds to program currently selected volume level. "P-VOL" and the current volume level will momentarily appear in the display. Press EQ to select between POP, JAZZ, CLASSIC, BEAT, ROCK and OFF (default) equalization curves. Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected). Press DISP to select between clock and different types of information, such as radio frequency, CD track/elapsed time or MP3/WMA song information. Press RESET upon initial installation or if abnormal operation occurs. Reset button is located on the front panel. XDM7615 OPERATION General Operation -Setup Menu Set the Clock With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE nn to adjust the hours and TUNE ll to adjust the minutes. Press DISP momentarily to save the selected time. 12/24-hour Clock The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00). Setup Menu Press and hold SETUP for more than 3 seconds to access the setup menu. Press SETUP momentarily to select between the menu functions and rotate the rotary encoder left/right to adjust or activate the desired function. Menu Function Options Action Loudness Curve LOUD OFF Disables the loudness function. LOUD ON Enables the loudness function. Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes. Tuner Frequency Spacing FREQ USA Programs the unit to USA tuner spacing. (200kHz for FM and 10kHz for AM) FREQ EUR Programs the unit to European tuner spacing. (50kHz for FM and 9kHz fo...

Напишите ваш отзыв об устройстве

Текст отзыва
Ваше имя:
Введите две цифры: