Оценок - 5, средний балл: 4 ( )

Инструкция по эксплуатации Kicker, модель ZX100.2

Производитель: Kicker
Размер: 342.78 kb
Название файла: 322e2d34-2d09-e304-910e-0910f3b9eabd.pdf
Язык инструкции:enesfr
Перейти к скачиванию

Фрагмент инструкции

Amplifier Serial Number: __________________________ Installation 1. Mounting Choose a structurally sound location to mount your Kicker amplifier. Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier. 2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint and corrosion free solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger) between the battery's negative post and the vehicle chassis is recommended. The ZX amplifier has dual input sensitivity differential RCA inputs which will receive either high or low level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifier, the ZX amplifier’s input level switch should be set to “LO” and a low-level signal should run from the source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifier using RCA interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can be delivered to the amplifier using the high-level speaker outputs on the source unit. Set the input level switch on the end panel of the amplifier to “HI”. Crimp and solder RCA connectors to the end of the KUNEK 10 - COMA + > INSTALLATION speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the RCA Inputs on the end panel of the amplifier as shown in Figure 1. Keep the audio signal cable away from factory wiring harnesses and other Figure 1 High-level Speaker Output Wire + + Core Cable To Source Unit power wiring. If you need to cross this wiring, cross it at a 90 degree angle. Ground or Shielding To Amplifi er > Install one 15 ampere fuse within 18” (45cm) of the battery and in-line with the 8 gauge connected to your amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it. 3. Confi guration The following diagrams show the most common configurations for your Kicker ZX series amplifier. Figure 2 Two Channel Operation (Stereo) Minimum Impedance of 2 ohms per channel in stereo operation +12V 18" (45cm) 24" (60cm)4" Fusecm) Ground RemoteTurn-On R+R-L+L- Signal In Source Unit Battery ZX. 2AMPLIFIER Figure 3 +12V 18" (45cm) 24" (60cm) KUNEK 10 - COMA Minimum impedance of 4 ohms while in bridged operation Ground Remote Turn-On Fuse Battery R+ R- Signal In Source Unit Bridge Wiring Bridged Operation (Mono) L+ L- Remote Turn-On +12V 18" +_+_ +_ (45cm) 24" (60cm) +_+ XOVER XOVER XOVER KUNEK 10 - COMA CONFIGURATION Figure 4 Minimum impedance of 4 ohms mono and 2 ohms per channel in stereo simultaneously Ground Remote Turn-On Fuse Battery High Pass High Pass Low Pass Signal In Source Unit Bridge Wiring Stereo and Mono Operation Simultaneously (SAMS) R+ R-L+ L- Performance Model ZX100.2 RMS Power in Watts, all channels driven @14.4 25 x 2 Volts, 4. stereo, . 1% THD+N @ 2. stereo, . 1% THD+N 50 x 2 @ 4. mono, . 1% THD+N 100 Length: in(cm) 8 1/4 (20.9) Specifi cations common to all models: Height: in(mm) 2 1/8 (54mm) Width: in(mm) 9 5/8 (244mm) Frequency Response, ± 1 db: 20 Hz - 20 kHz Signal-to-Noise Ratio: >95db, a-weighted, re: rated power Low Level: 125mV-5V Input Sensitivity: High Level: 250mV-10V 12 db/Octave High Selectable Electronic Crossover: 12 db/Octave Low Bass Boost: Variable 0 to @ 40Hz Note: To get the your we recommend Operation 1. Automatic Turn-On Selection The ZX series offers three different automatic turn-on modes that can be selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode causes the REM terminal to have +12V out for turning on additional amplifi ers. Remote Turn-On Set the switch to +12V to use the remote turn-on lead from your source unit. Run 18 Ga wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the amplifi er’s positive and negative power terminals. This is the preferred automatic turn-on method. DC Offset Turn-On If Remote Turn-On is not an option, the next best setting is DC Offset. The DC Offset mode detects a 6 volt surge from the HI Level speaker outputs when the source unit has been turned on. Signal Sense Turn-On The Audio setting is the fi nal alternative for Automatic turn-on. This is a Signal Sense turn-on method that detects the incoming audio signal from your source unit and automatically turns on the amp. This turn-on method will not work properly if the input gain control is not set appropriately. 2. Input Le...

Напишите ваш отзыв об устройстве

Текст отзыва
Ваше имя:
Введите две цифры: