Войти:
Скачали: 0   Размер: 173 kb   Производитель: Panasonic  
Категория: Видеонаблюдение
@name

please rood :-«г rsrj“cnsecmctocet> CAUTION : When the lens becomes dirty, wipe it using a dry and scrt doth or a cloth soaked with alcohols. Ho not use chemical e.g thinner or benzine for cleaning because this may damage the surface (1) Make sure the Selection switch on the camera is set to DC position. {Fig. 1) Fig.l Notes : • Some cameras do not have the Lens Selection Switch. • The site of Lens Selection Switch is different by ;he cameras. Caution : Always set the flange-back adjustin

Скачали: 0   Размер: 213 kb   Производитель: Panasonic  
Категория: Видеонаблюдение
@name@name

lens is used icv black and white cameras, only. 0} Make sure, ihat the Lens.Selection Switch orí The roar o* The camera is .set ai DC position. (Fig. ? ) Fig. 1 CAUTION : Always set the (larga-back adjust ngring to fully dock wise (Omojnt side! by iocsifyj one screw on tne rsng before mount np rbc I cot, The inner glass and CCD image sensor might 6« damage by the lens otherwise. 12) Mount t^n lens b/ turning it clockwise onto the Istis. mount of the camera. (3) Connect the lens cable to the

Скачали: 0   Размер: 545 kb   Производитель: Panasonic  
Категория: Видеонаблюдение
@name

Скачали: 0   Размер: 117 kb   Производитель: Panasonic  
Категория: Видеонаблюдение
@name

1) (4- Loosen sc-ewson the flange-back acjuatm; rirvj (Turn :he -lange-bttck i xj nr,) i > ir»o <2cairec position.) CAUTION: Do not turn this ling too much coijntorclock wise as this might damage the Inner

Скачали: 0   Размер: 650 kb   Производитель: Panasonic  
Категория: Видеонаблюдение
@name

ON: Turns on burst signal output. This is the factory default setting. OFF: Turns off burst signal output. Note: With some monitors and VCR models, output of a camera images in the black and white mode will not display a proper image unless a burst signal is provided. Select ON for this setting when using equipment that requires a burst signal. -29 (11) Auto Focus (AF MODE) 1. Move the cursor to AF MODE, and then tilt the joystick left or right to select an auto-focus mode setting. MANUAL S.M.L

Скачали: 0   Размер: 2 mb   Производитель: Panasonic  
Категория: Видеонаблюдение
@name@name@name@name

The 4-bit DIP switch is used for ON RS485 termination. 1234 4-bit DIP SW Fall Prevention Wire BP 1 Function Switch ON Termination ON position OFF Termination OFF * BP 2 BP 3 BP 4 Function Switch ON ON ON Half duplex (2 line) position OFF OFF OFF Full duplex (4 line) * Notes: • Defaults are marked with *. • BP stands for Bit Position. • Full duplex is not available in a daisy chain connection. (Panasonic system controllers only) 5. Mounting the camera (1) Aim the "START" arrow at the bent portion

Скачали: 0   Размер: 1 mb   Производитель: Panasonic  
Категория: Видеонаблюдение
@name@name

Synchronization Setting (SYNC) 1. Select a sync mode. VD2: Multiplexed vertical drive, highest priority LL: Line-Lock, follows the phase of supplied AC power, 2nd priority INT: Internal sync, lowest priority Notes: • Selection is not available when VD2 is added to the camera. Selection from LL is available when the respective sync is added. • When LL is selected, phase adjustment is required. 2. Line-Lock Vertical Phase Adjustment (V PHASE) • Select LL and press the [SET] button. • Prepare a dua

Скачали: 0   Размер: 176 kb   Производитель: Panasonic  
Категория: Видеонаблюдение
@name

3. Press I(S) to determine the CAMERA ID. To erase all characters in the editing area Move the cursor to RESET and press I(S). All characters in the editing area disappear. To determine the display position of the CAMERA ID 1. Move the cursor to POSI, and press WV-CW474 Highlighted I(S). The display at right appears and the CAMERA ID is highlighted. 2. Move the CAMERA ID to the desired position by pressing I(L) / I(R) / I(U) / I(D). 3. Press I(S) to fix the position of the CAMERA ID. The mode re

Скачали: 0   Размер: 582 kb   Производитель: Panasonic  
Категория: Видеонаблюдение
@name

The following functions are built in. SETTING PROCEDURESSETUP 1. Camera Identification (CAMERA ID) Setting 1. CAMERA SETUP MENU Moves the cursor upward and selects items in the CAM SET UP menu. (1) Auto Light Control (ALC) You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera This camera utilizes an on-screen user setup menu. (2) The SUPER-D2 function eliminates interference by strong background lighting which Color CCTV Cameras makes the camera picture dar

Скачали: 0   Размер: 1 mb   Производитель: Panasonic  
Категория: Видеонаблюдение
@name@name

FLOOR 1 Character Cursor Character Area Command Editing Area Pointer Highlighted 4. To specify the ID display position: 1. Select "POSI" and press the [SET] button. > The entered camera ID will be highlighted on the screen. 2. Move it into the appropriate position and press the [SET] button. > The position is determined and the screen will return to the "CAMERA ID" menu. Note: • Keep pressing any of [LEFT], [RIGHT], [UP], or [DOWN] button for a second or more to move the camera ID faster as nece





Категории