Оценок - 3, средний балл: 3.7 ( )

Инструкция по эксплуатации Porter-Cable, модель Rockwell 863538-0811

Производитель: Porter-Cable
Размер: 3.15 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию

Фрагмент инструкции

Do not operate tools rated A.C. only on D.C. current. To do so may seriously damage the tool. ■ EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found below. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amperes. RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS Length of Cord in Feet 115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft. 230V 50 Ft. 100 Ft. 200 FT. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft. Nameplate Ampere Rating 0 2 18 18 18 16 16 14 14 12 12 2 3 18 18 16 14 14 12 12 10 10 3-4 18 18 16 14 12 12 10 10 8 4-5 18 18 14 12 12 10 10 8 8 5 6 18 16 14 12 10 10 8 8 6 6 8 18 16 12 10 10 8 6 6 6 8-10 18 14 12 10 8 8 6 6 4 10-12 16 14 10 8 8 6 6 4 4 12-14 16 12 10 8 6 6 6 4 2 14-16 16 n 10 8 6 6 4 4 2 16-18 14 12 8 8 6 4 4 2 2 18-20 14 12 8 6 6 4 4 2 2 fmwom Your ROCKWELL Hammer is designed for drilling holes in concrete and like materials - for setting self-drilling anchors - for chipping, chiseling, edging, channeling, scaling and other hammering where rotation is not required. 4 OPERATING INSTRUCTIONS HOW TO use THE HAMMER Make sure hammer is disconnected from power circuit« •1. Install bit or other accessory as outlined in section, "TO INSTALL BITS AND ACCESSORIES.” 2. If the operation to be done requires the use-of the depth gage. Install and adjust it as outlined in, f,TO INSTALL AND ADJUST DEPTH GAGE.” ' 3« Put on safety goggles. 4. - Connect hammer to power circuit. Make sure the power circuit voltage is the same as that shown on the specification plate on the hammer. 5. Set Hammer and Drill Indicator in the "D## positiorj. 6. Grasp switch handle with one hand and the auxiliary handle with the other hand. 7. Place tip of bit or other acc®s$ory against the work and exert slight pressure. 8. ■ Depress switch trigger to. Start hammer. NOTE - HAMMER REQUIRES NO WARM-UP PERIOD, TOOL MAY BE PLACED IN OPERATION IMMEDIATELY, Apply steady, even pressure during the complete operation. 10. As soon as the operation is, completed, release switch trigger. 11. CAUTION -'Turn tool off when not in use to avoid excessive idling. Keep latch mechanism in .proper working condition. ■ Replace latch spring if broken pr worn. This is your' assurance that your hammer'is protected against undue stress and damage. 12. When using tapered shank drill bits, make sure bit shank and tapered seat in the holder are clean and free of grease. Install drill in drill holder. Now, install drill assembly in hammer, following the instructions given'in ”TO INSTALL 'BITS AND ACCESSORIES.* * 'To remove drill bit from the holder, first remove the drill assembly from the hammer. Next, Insert the drift key in the slot in the holder with the tapered face toward the bit. Drive, key to loosen drill bit. 5 TO INSTALL BITS AND ACCESSORIES 1. 'Disconnect machine from power source. 2. Clean bit or accessory shank end and apply a light film of grease to surface of shank. 3» Using a bar, (A) or si mi liar object, pry latch bolt head (B) out of counterbore of latch (C), as shown in Fig-1„ IF if). 1 FI«. 2. 4. Pivot latch (C) to the open position, as shown in Fig. 2; Ft9. 3 5, Install bit (D) or other rotating accessory into nose and pivot latch (C) to' locked position, as shown in Fig. 3, 6 6. When installing ..a ' NONROTATING type of accessory, bull point chisel, ■ slotting tool»' or the like, be sure the flats on the shank of accessory are positioned within the slot in the latch and the latch is pivoted to'the locked position. - . HAMMER AND DRILL INDICATOR A "T" shaped lever (A), having a "WHITE” end and a "BLACK” end, is located beneath the nosepiece Fig, 4, F*g. 4 When the "WHITE" end is towards the side of the nose marked "D”, a revolving and'hammering action is delivered to any accessory installed in the hammer. The hammer.may.be used with the lever in this position when'using either .Rotating or Nonrotating accessories. Nonrotating accessories will not rotate due to the design of the shank« When the "WHITE" end is towards the side of the nose marked "HM only a hammering action is produced. ONLY Nonrotating accessories may be used with the liver in the position. INSTALLING SELF-DRILLING ANCHORS An adapter is furnished with your hammer that accomodates Ghuck Heads used to install self, drilling anchors. It may be found help full to start the drilling operation for self drilling anchors with .the Hammer and .Drill 'indicator Lever set in the' "H" position until a spot is started to prevent the anchor from wandering. Then turn to "D" position for completing the hole. After the hole has been drilled, the, lever is turned to the "H,r position for driving the anchor into th...

Эта инструкция также подходит к моделям:
Прочие инструменты - Rockwell 601 (3.15 mb)

Напишите ваш отзыв об устройстве

Текст отзыва
Ваше имя:
Введите две цифры: