Оценок - 3, средний балл: 3.7
Перейти к скачиванию
Инструкция по эксплуатации Kenwood, модель KDC-1023
It may not correctly play discs which do not have the mark. • A CD-R or CD-RW that hasn’t been finalized can’t be played. (For the finalization process refer to your CD-R/CD-RW writing software, and your CD-R/CD-RW recorder instruction manual.) — 5— CD storage • Don’t place them in direct seat or dashboard etc.) temperature is high. • Store CDs in their cases. General General English Release button (KDC-4023/KDC-3023/KDC- AM FM . 4ud SRC ATT/ #1 #3 CLK/ Q/ LOUD ADJ AUD KDC-4023/KDC-3023/KDC-2023 ATT indicator LOUD indicator SYSTEM Q indicator ATT indicator LOUD indicator SYSTEM Q indicator KDC-1023/KDC-1023S Clock indicator Clock display Clock indicator Clock display Turning ON the Power Press the [SRC] button. Turning OFF the Power Press the [SRC] button for at Selecting the Source Press the [SRC] button. Source required Display Tuner "TUnE" CD "CD" External disc "DISC" (Function of the KDC-4023/KDC-3023/KDC-2023) Standby (Illumination only mode) "OFF" Volume Increasing Volume Press the [ u] button. Decreasing Volume Press the [ d] button. Attenuator Turning the volume down quickly. Press the [ATT] button. Each time the button is pressed the Attenuator turns ON or OFF. When it’s ON, the "ATT" indicator blinks. Loudness Compensating for low and high tones during low volume. Press the [LOUD] button for at least 1 second. — 6— Each time the button Each time the button 4 Adjust the Audio When it’s ON, "LOUD" indicator Press the [ 4] or [ . ] button. System Q Adjustment Item Display Range Bass level "BAS" –8 — +8 You can recall the best sound the music. 1 Select the source to set Press the [SRC] button. 2 Select the Sound type Press the [Q] button. Each time the button is pressed the sound setting Sound setting Display Middle level "MID" –8 — +8 Treble level "TRE" –8 — +8 Balance "BL" Left 15 — Right 15 Fader "FD" Rear 15 — Front 15 5 Exit Audio Control mode Press the [AUD] button. Speaker Setting Flat "SQ-1" Fine-tuning so that the System Q value is optimal when Rock "SQ-2" the speaker type. Top 40 "SQ-3" 1 Enter Standby Pops "SQ-4" Press the [SRC] button. Jazz "SQ-5" Select the "OFF" display. Easy "SQ-6" 2 Enter Speaker Setting mode • Each setting value is changed with the (page 7). First, select the speaker type with the Speaker setting. Press the [Q] button. • When the System Q setting is changed, the Bass, Middle, and 3 Select the Speaker type Treble set in audio control replace the System Q values. Press the [ 4] or [ . ] button. Audio Control Each time the button is pressed the setting switches as shown below. 1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted Speaker type Display OFF "SP-F" For the OEM speaker "SP-O" For 6 & 6x9 in. speaker "SP-6" For 5 & 4 in. speaker "SP-5" 4 Exit Speaker Setting mode Press the [Q] button. — 7— General General Clock Display Press the [CLK] button. Each time the button is OFF. When it’s ON, the clock indicator is ON. Adjusting Clock 1 Select the clock display Press the [CLK] button. 2 Enter clock adjustment mode Press the [CLK] button for at least 2 seconds. The clock display blinks. 3 Adjust the hours Press the [FM] or [AM] button. Adjust the minutes Press the [ 4] or [ . ] button. 4 Exit clock adjustment mode Press the [CLK] button. Function of the KDC-4023/KDC-3023/KDC-2023 DSI (Disabled System Indicator) A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. 1 Turn the power OFF Press the [SRC] button for at least 1 second. 2 Set the DSI While pressing the [#1] and [#3] button, press the [SRC] button. Each time the step 1 and 2 operation is done the DSI turns ON or OFF. Function of the KDC- Theft Deterrent Faceplate The faceplate of the unit can helping to deter theft. Removing the Faceplate Press the Release button. The faceplate is unlocked, allowing you to • The faceplate is a precision piece of equipment and damaged by shocks or jolts. For that reason, keep the faceplate its special storage case while detached. • Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Reattaching the Faceplate 1 Align the projections on the unit with the grooves on the faceplate. 2 Push the faceplate in until it clicks. The faceplate is locked in place, allowing you to use the unit. — 8— Tuner features Tuner features FM/ AM CRSC . 4 SRC #1 - 6 AUTO/ AME KDC-4023/KDC-3023/KDC-2023 ST indicator Preset station number CRSC indicator KDC-1023/KDC-1023S Band display Frequency display AUTO indicator ST indicator Band display Preset station number Frequency display AUTO indicator CRSC indicator Choose the tuning Press the [AUTO] button. Each time the button is pressed mode switches as shown below. Tu...
Эта инструкция также подходит к моделям:Автомагнитолы - KDC-1023S
(429.49 kb)Автомагнитолы - KDC-2023
(429.49 kb)Автомагнитолы - KDC-3023
(429.49 kb)Автомагнитолы - KDC-4023