Войти:
Скачали: 4   Размер: 344 kb   Производитель: Yamaha  
Категория: Акустика
@name

Die Frequenzen uber der mit diesem Regler eingestellten Frequenz werden abgeschnitten (sie werden nicht wiedergegeben). .Lautstarkeregler (VOLUME) Stellen Sie mit diesem Regler die Lautstarke ein. @Haupt-Netzschalter (POWER) Normalerweise soll dieser Schalter in der Stellung ON sein. Wenn das Gerat langere Zeit nicht verwendet werden soll, stellen Sie den Schalter auf OFF. ¤Auto-Bereitschaft-Schalter (AUTO STANDBY) Mit diesem Schalter kann die automatische Bereitschaftsfunktion aktiviert werden.

Скачали: 16   Размер: 340 kb   Производитель: Yamaha  
Категория: Акустика
@name

Normally, set the switch to the LOW position. To cancel this function, set the switch to the OFF position. * Change the setting of this switch only when the power of this unit is on standby (by setting the STANDBY/ON button to OFF). Automatic Standby function When you play a source, the power of this unit turns on automatically by sensing audio signals input to this unit. This unit turns into the standby mode automatically if the source being played is stopped or the low frequency input signal i

Скачали: 8   Размер: 3 mb   Производитель: Yamaha  
Категория: Акустика
@name@name@name@name@name@name@name

(Refer to pages 6 and 7 for details.) Connecting to line output (pin jack) terminals of the amplifier Connect the main speakers to the speaker output terminals of the amplifier. . To connect with a YAMAHA DSP amplifier (or AV . When connecting the subwoofer to the SPLIT receiver), connect the SUBWOOFER (or LOW PASS etc.) SUBWOOFER terminals on the rear of the DSP amplifier, terminal on the rear of the DSP amplifier (or AV receiver) be sure to connect the L/MONO INPUT2 terminal to the to the L/MO

Скачали: 2   Размер: 6 mb   Производитель: Yamaha  
Категория: Акустика
@name@name@name@name@name@name@name

Make sure that the + and – polarity markings of the speaker cables are observed and set correctly. If these cables are reversed, the sound will be unnatural and lack bass. Caution Do not let the bare speaker wires touch each other, because this could damage the subwoofer or the amplifier, or both of them. ¦Before connecting Remove the insulation coating at the extremity of each speaker cable by twisting the coating off. Good No Good 10mm (3/8”) ¦How to connect: 1 Loosen the terminal’s knob, as s

Скачали: 1   Размер: 6 mb   Производитель: Yamaha  
Категория: Акустика
@name@name@name@name@name@name@name

4 Connecting to line output (pin jack) terminals of the amplifier .................................................... 4 1 Connecting to speaker output terminals of the amplifier .......................................................... 6 Connecting to the INPUT1/ OUTPUT terminals of the subwoofer .........................................................8 Plug in the subwoofer to the AC outlet ......................8 2 CONTROLS AND THEIR FUNCTIONS .................... 9 AUTOMATIC POWER-SWITCHIN

Скачали: 19   Размер: 546 kb   Производитель: Yamaha  
Категория: Акустика
@name

Если Ваш усилитель оборудован двумя наборами разъемов для фронтальной акустики и оба разъема могут выдавать сигнал одновременно. Соедините один набор фронтальных выходных разъемов на усилителе с входом INPUT1 на сабвуфере, а второй набор фронтальных выходных разъемов на усилителе с фронтальными громкоговорителями. Установите усилитель на одновременную подачу сигнала к обоим разъемам. Если Ваш усилитель оборудован только одним набором фронтальных выходных разъемов, то обратитесь к следующей стран

Скачали: 36   Размер: 2 mb   Производитель: Yamaha  
Категория: Акустика
@name@name@name@name@name@name@name

3 Placement .................................................................. 3 Connections ............................................................... 4 Controls and their functions ....................................... 7 FEATURES Adjusting volume ........................................................ 8 Advanced YAMAHAActive Servo Technology..........10 Troubleshooting ........................................................ 11 Specifications ...........................................

Скачали: 1   Размер: 3 mb   Производитель: Yamaha  
Категория: Акустика
@name@name@name@name@name@name@name

2 Insert the bare wires. 3 Release your finger from the tab to allow it to lock securely on the cable’s wire end. 4 Test the firmness of the connection by pulling lightly on the cable at the terminal. + 1 2 – Notes • Do not let the bare speaker wires touch each other, because this could damage the subwoofer or the amplifier, or both of them. • For connection, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the connections are faulty, no so

Скачали: 29   Размер: 3 mb   Производитель: Yamaha  
Категория: Акустика
@name@name@name@name@name@name@name

ADJUSTING THE SUBWOOFER BEFORE USE ADJUSTING THE SUBWOOFER BEFORE USE This subwoofer’s frequency characteristics 40 50 60 70 80 90 dB HIGH CUT 50 Hz HIGH CUT 150 Hz HIGH CUT 90 Hz 20 50 100 200 500Hz Frequency response graph* The figures below show the optimum adjustment of each control and the frequency characteristics when this subwoofer is combined with a typical front speaker system. ¦EX.1 When combined with a 4” or 5” (10 cm or 13 cm) acoustic suspension, 2 way system front speakers If you

Скачали: 31   Размер: 8 mb   Производитель: Yamaha  
Категория: Акустика
@name@name@name@name@name@name@name

Instead, connect the subwoofer to the speaker output terminals of the amplifier. (Refer to pages 8-11.) • When connecting to a monaural line output terminal of the amplifier, connect the L /MONO INPUT2 terminal. • When connecting to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT terminals on the rear panel of the subwoofer. If connected, they will not produce sound. 6 English ¦Using one subwoofer CONNECTIONS Subwoofer Amplifie





Категории