Войти:
Скачали: 3   Размер: 215 kb   Производитель: Dakota Digital  
Категория: Осветительные приборы
@name

If lenses are in bad shape a new set is recommended. 6. Remove the lock nuts and aluminum back plate from the back of the new LED assembly. 7.Insert the new LED assembly through the hole where the original bulb and connector were. Use caution when feeding the wires through to avoid damaging the wire insulation. 8.Feed the wires through the large hole in the back plate and attach the back plate onto the backside of the housing.The flat side of the mounting disk should betoward the outsideand thes

Скачали: 2   Размер: 222 kb   Производитель: Dakota Digital  
Категория: Осветительные приборы
@name

B Kit Includes: m, m Installation: 1. Remove the screws and the tail light lens. 2. Remove the tail light bulb. 3. Now is a good time to clean or replace the lens and housing if necessary. 4. The new LED assembly will mount into the original light bulb socket. Push it into the socket and turn it clockwise to lock it in. 5. Repeat for the other tail light. 6. Test the tail lights, brake lights, and turn signals. If the turn signals do not flash, you will need to upgrade your flasher. If

Скачали: 1   Размер: 151 kb   Производитель: Dakota Digital  
Категория: Осветительные приборы
@name

If the lenses are in poor condition a replacement set is recommended. 7. Make sure the housings and lenses are clean and dry. DO NOT remove backing from tape yet! Place the light diffuser onto the back of the lens. Check for proper fitment of diffuser to inside of lens and note the places where the tape touches the lens. MAN#650204 8. DO NOT remove the backing from the tape yet! Place the LED assembly in the housing. The wide black bar on the wire side of the LED assembly is marked to show wh

Скачали: 1   Размер: 224 kb   Производитель: Dakota Digital  
Категория: Осветительные приборы
@name

There are four screws holding each lens in place. 2. Remove the light bulbs. 3. Now is a good time to clean the lenses and housings. If lenses are in bad shape a new set is recommended. 4. DO NOT remove the tape from the LED assemblies yet! MAN#650203 5. Test fit the assembly into the tail light housing as shown below to make sure it aligns correctly. 6. Before mounting the new LED assembly into the housing, plug the bulb base into the stock bulb socket and test the tail lights and flasher

Скачали: 1   Размер: 199 kb   Производитель: Dakota Digital  
Категория: Осветительные приборы
@name

Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. The housing may need to be removed from the car on the ’71-’72 Chevelle. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the screw and aluminum back plate from the back of the new LED assembly. LED assembly standard back back for ‘71-‘72 Chevelle (attached to the assembly) (packaged separately) 6. Insert

Скачали: 1   Размер: 126 kb   Производитель: Dakota Digital  
Категория: Осветительные приборы
@name

Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Insert the supplied rubber grommet into the hole where the original light socket was located. This will protect the wires from rubbing on the metal edge. 6. Make sure the stock lens gasket is removed from the housing and place the supplied drill template into the

Скачали: 2   Размер: 140 kb   Производитель: Dakota Digital  
Категория: Осветительные приборы
@name

Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. 4. Now is a good time to clean or replace the lens and housing if necessary. 5. Remove the two screws and aluminum plate from the back of the new LED assembly. 6.Insert the new LED assembly through the hole where the original bulb and connector were. Be careful when feeding the wires throughto avoid damaging insulation. 7.Feed the wires through the larger hole in themoun

Скачали: 5   Размер: 168 kb   Производитель: Dakota Digital  
Категория: Осветительные приборы
@name

Remove the tail light assembly from the vehicle by removing the original bulb sockets from the housing. Then remove the housing hardware so it can be removed from the car. Remove the housings from the vehicle carefully so the housing to body gaskets are not damaged. 2. Next remove the lens. The 67-68 Camaro has six screws that hold the housing halves together which will need to be removed to gain access to lens. The 70-73 Camaro lens has tabs locking it into the plastic housing. Pry the tabs gen

Скачали: 1   Размер: 159 kb   Производитель: Dakota Digital  
Категория: Осветительные приборы
@name

There are four screws holding each lens in. 2. Remove the tail light bulbs. 3. We recommended that the lens and housings be cleaned to insure proper mounting and visibility of the LED assembly. If the lenses are in bad shape a new set is suggested. 4. DO NOT remove the tape from the led assemblies yet! 5. Test fit the assembly into the lens as shown below to make sure it aligns correctly. 6. Make sure you have BOTH lenses clean and dry so the single use primer applicator can be used for bot

Скачали: 1   Размер: 177 kb   Производитель: Dakota Digital  
Категория: Осветительные приборы
@name

Remove the tail light housing from the vehicle. 2. Remove the bulb connector from the back of the housing. 3. Remove the 4 screws that hold the trim and lens. Remove the trim and tail light lens from the tail light housing. 4. Now is a good time to clean or replace the lens and housing if necessary. 5. Note that there are two different LED assemblies. One for the driver side and one for the passenger side. Select the correct assembly for the tail light housing. Remove the two locking nuts and fl





Категории