Оценок - 3, средний балл: 3.7 ( )

Инструкция по эксплуатации Rotel, модель RSP980

Производитель: Rotel
Размер: 6.16 mb
Название файла: rsp980_eng.pdf
Язык инструкции:en
Перейти к скачиванию

Фрагмент инструкции

To reduce the risk of electric shock do not remove any parts of the RSP-980. A This symbol is to alert the user of important operating instructions in the owner's information accompanying the RSP-980. Read all the instructions before connecting or operating the RSP-980. Pay particular attention to the safety information. Keep this manual so you can refer to these safety instructions. WARNING: There are no user serviceable parts inside. Refer all servicing to qualified service personnel. Please do not open the cabinet as this will expose you to the risk of shock from potentially dangerous high voltages. Unauthorized attempts at repair or modification will void your warranty.. WARNING: To reduce the risk of fire or electric shock, do not expose the RSP-980 to moisture or water. Do not allow foreign objects to get into the enclosure. If the unit is exposed to moisture, or a foreign object gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a qualified service person for inspection and necessary repairs. If you wish to clean the RSP-980's cabinet, please use a soft, DRY cloth. Don't use cleaning compounds or solvents as they may dull the finish, remove the labels, or damage circuitry if any residue falls inside. Place the RSP-980 on a fixed, level surface strong enough to support its weight. Keep the RSP-980 away from radiators, heat registers, stoves, or any other appliance that produces heat. Connect the RSP-980 to the power outlet only with the supplied power supply cable. The cable should be connected to a properly grounded 3-pin wall outlet. Do not modify the supplied cable in any way. Do not use extension cords. Do not route the power cord where it will be crushed, pinched, bent at severe angles, exposed to heat, or damaged in any way. If the cable shows any sign of wear or damage, immediately stop using it and obtain a proper replacement from a qualified service agency or from the Rotel National Service Center. If the RSP-980 shows signs of improper operation, or if it has been dropped or damaged in any way, immediately disconnect the power cord from the wall. Take the RSP-980 to a qualified service person for inspection and necessary repairs. RSP-980 Contents (circled numbers refer to illustrations on the following page) Figure 1: RSP-980 Features _ 4 Figure 2: Audio Components Hookup_ 5 Figure 3: Video Components Hookup (RCA connections) 6 Figure 4: Video Components Hookup (S-Video)_7 Figure 5: Zone 2 Connections_8 Figure 6: RR-930 Features_9 Getting started _9 RSP-980 key features 9 Unpacking the RSP-980 9 Where Does It Go? 10 Notes On Cable Routing 10 Front panel controls_10 Standby LED Indicator ^ 10 Standby Switch ^ 10 Remote Sensor 10 Master Volume Control Q 10 Listening Source Selector Buttons ^ 11 Recording Source Selector Buttons 11 Surround Sound Mode LED Indicators ^ 11 Tone Controls ^ 11 Movie Filter Q 12 Tape Monitor Q 12 5.1 Channel Input Q 12 RR-930 Remote Control_12 Standby Switch Q 12 Master Volume Controls Q 12 Listening Source Selector Buttons 12 Mute Button (remote only) ^ 12 On-Screen button (remote only) 12 Surround Mode Buttons (remote only) ^ 13 Delay Time buttons (remote only) ^ 13 Center Focus Button (remote only) o 14 Balance Check (remote only) ^ 14 The On-Screen Display_14 Operating Screen 14 Bypassing the On-Screen Display 15 Rear Panel Input Signal Connections_15 RCA Source Audio and Video Inputs: © 15 S-Video Source Inputs ^ 15 5.1 Channel Audio Input 16 Rear Panel Output Signal Connections _16 RCA-type Source Audio and Video Outputs 16 S-Video Outputs 17 Video 3 S-Video Selector 17 Main Preamplifier Audio Outputs (RCA) 17 Main Preamplifier Audio Outputs (Multi-pin) 17 TV/Monitor Video Output & Selector Switch 18 Tape Monitor Audio Outputs 18 Rear Panel Zone 2 Connection _18 Zone 2 Audio Outputs 19 Remote External Sensor/Repeater Jacks 19 Rear Panel Speaker Configuration Switches_ 19 Surround Hi-pass (On/Off) (J) 19 Front Hi-pass (On/Off) ^ 19 Center Mode (Normal/Phantom/Wide) 20 Rear Panel AC Power Connections _20 AC power cord 20 AC Convenience Outlet ££) 20 System Calibration_20 What You'll Need 21 How to calibrate your system 21 Using the RSP-980 _22 Overall Design 22 DSP Modes 22 Some Comments about Speakers_23 Tonal Balance 23 Speaker Placement 23 RSP-980 Specifications_25 RDTEL SURROUND SOUND PROCESSOR RSP-980 Figure 1: RSP-980 Features RSP-980 Figure 2: Audio Components Hookup CD PLAYER It FT PKXT AM/FM TUNER OUTPUT LIFT PKJKT CASSETTE RECORDER -®-1' 0-1 r€> Li FT _ _ I.......i ROTEL RSP-980 ROTEL SURROUND SOUND PROCESSOR RSP-980 Figure 3: Video Components Hookup (RCA connections) RSP-980 Figure 4: Video Components Hookup (S-Video) RDTEL SURROUND SOUND PROCESSOR RSP-980 Figure 5: Zone 2 Connections CD PLAYER 0 ' N 0 V_ J ZONE 2 IR REPEATER ZONE 2 SPEAKERS RSP-980 Figure 6: RR-930 Features Gettin...

Напишите ваш отзыв об устройстве

Текст отзыва
Ваше имя:
Введите две цифры: