Войти:

Milwaukee V-101

Скачали: 0Размер: 77 kb    Производитель: Milwaukee  
Категория: Шлифовальные станки

Milwaukee Sries 6521

Скачали: 0Размер: 1 mb    Производитель: Milwaukee  
Категория: Дрели и шуропопверты

Always replace a damaged extension cord or have it repaired by a qualified person before using it. • Protect your extension cords from sharp objects, excessive heat and damp or wet areas. Recommended Minimum Wire Gauge for Extension Cords* Nameplate Amperes Extension Cord Length 25' 50' 75' 100' 150' 200' 0 - 5 16 16 16 14 12 12 5.1 - 8 16 16 14 12 10 -8.1 - 12 14 14 12 10 -- 12.1 - 15 12 12 10 10 -- 15.1 - 20 10 10 10 -- - * Based on limiting the line voltage drop to five volts at 150% of the r

Milwaukee S-114G

Скачали: 0Размер: 63 kb    Производитель: Milwaukee  
Категория: Дрели и шуропопверты

Milwaukee Rotary Hammer

Скачали: 3Размер: 1 mb    Производитель: Milwaukee  
Категория: Прочие инструменты

Unplug the tool before changing accessories or making adjustments. WARNING Selecting Speed The speed control dial on these hammers allows the user to adjust the rotating speed (RPM) and the impact rate (BPM) of the tool. To change the speed, set the speed control dial to the desired setting. • Lower speeds provide more control when starting holes and reduce 'spalling' on breakthrough. Spalling occurs when pieces of material chip off around the drilled hole on breakthrough. When chiseling in soft

Milwaukee RAVL42

Скачали: 0Размер: 7 mb    Производитель: Milwaukee  
Категория: Вентиляторы

Close the tap gently but securely after completing the check. The manifold (outlet) tap is to the right of the inlet tap. To check manifold pressure (with the fireplace burning at the high burn setting) insert a small flat bladed screwdriver into the tap and turn a half turn counterclockwise. Cover the tap with the line from the manometer and check the pressure. Again close the tap gently but securely after completing the check. Check the taps for gas leaks with a gas leak test solution (retight

Milwaukee R-600

Скачали: 0Размер: 50 kb    Производитель: Milwaukee  
Категория: Дрели и шуропопверты

Milwaukee Pistol Drill

Скачали: 1Размер: 102 kb    Производитель: Milwaukee  
Категория: Дрели и шуропопверты

Milwaukee OES-80CS

Скачали: 0Размер: 1 mb    Производитель: Milwaukee  
Категория: Шлифовальные станки

If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools. For the name of an Authorized Service Center in your area call 1-800-274-6848. MORE INFORMATION WMH Tool Group is consistently adding new products to th

Milwaukee MK-Manta I

Скачали: 0Размер: 1 mb    Производитель: Milwaukee  
Категория: Дрели и шуропопверты

Step 2 Install the leveling screws (8), screwing four (4) into each base. Step 3 Install the feed handles (1) and knobs (2) by screwing one knob onto the end of the handle, then slip thru hub and attach other knob. Step 4 Remove the Manta from the vacuum base by removing the nut and bolt that holds the main assembly to the vacuum base. Set the Manta aside, observing the following precaution. Turn the vacuum base over. Press the gasket into the groove in the underside of the base. The gasket is c

Milwaukee M-708448

Скачали: 0Размер: 518 kb    Производитель: Milwaukee  
Категория: Шлифовальные станки

5) to the support rod (D, Fig. 5) by tightening the hex cap screw (E, Fig. 5) against the flat on the support rod. Tighten the jam nut. 18. Raise the table to a good height and tighten two set screws on the bracket. 19. Mount the small bracket between the backside of the extension bracket and the sander using two hex cap bolts, two lock washers and two flat washers. 20. Connect the sander to the power source, turn on the power to the machine just enough to start the belt rotating and then turn o





Категории