Войти:

Allstar Products Group SUPER BELT MVP-SB

Скачали: 0Размер: 6 mb    Производитель: Allstar Products Group  
Категория: Автоматические ворота

Product Features ................................................... 2 Component Identification..................................... 3 Identify Your Door Type ........................................ 3 Important Installation Instructions........................ 4 Assembly Instructions........................................... 5 Installing the Opener ............................................. 7 Mounting the Front Bracket ................................ 7 Mounting the Power Head..............

Allstar Products Group Paint Sprayer

Скачали: 0Размер: 45 kb    Производитель: Allstar Products Group  
Категория: Распылители краски

Prevents damage to crankshafts and piston cylinder walls by protecting exposed piston rod bolts, and at the same time, safely guides piston rods during removal and installation. TO REMOVE PISTON: 1. Remove nuts from piston rod bolts. 2. Place small adapters into prong ends and onto rod bolt ends. 3. Tap base of tool with palm of hand or hammer to break loose rod cap union. 4. Remove bottom rod cap and small adapters. 5. Place prong ends of tool onto piston rod bolts and push on base to rem

Allstar Products Group MVP-SQ

Скачали: 0Размер: 1 mb    Производитель: Allstar Products Group  
Категория: Автоматические ворота

Connect to terminals 0 and 1 as shown in the illustration below. Support the wire near the operator with wire ties. Step 5: Install the Control Button Warning Label supplied with your opener near the standard wall push button (see illustration next page). WARNING A CHILD OPERATING THE DOOR CONTROLS RISKS INJURY — OR DEATH — TO HIMSELF (HERSELF) AND OTHERS. DO NOT ALLOW CHILDREN TO OPERATE ANY DOOR CONTROLS. MOUNT THE PUSHBUTTON AT LEAST 5 FEET FROM THE FLOOR, OUT OF REACH OF CHILDREN. INSTALLATI

Allstar Products Group MVP-SB

Скачали: 0Размер: 2 mb    Производитель: Allstar Products Group  
Категория: Автоматические ворота

Allstar Products Group MVP-831E

Скачали: 0Размер: 326 kb    Производитель: Allstar Products Group  
Категория: Радиоприемники

Check the power connections to the receiver. There must be at least 20 VAC at the receiver power connections. (If a 24V system). Review the code switch and the selector switch settings then reprogram the receiver.. Try a different code switch setting. Check the antenna installation. Wait one minute for the receiver to “warm-up”. Check battery in transmitter. RECEIVER “CLICKS” WHEN ANY TRANSMITTER BUTTON IS PUSHED, BUT NOTHING ELSE HAPPENS. Check the wire & connections in the STOP circuit. Refer

Allstar Products Group MVP 110927

Скачали: 0Размер: 244 kb    Производитель: Allstar Products Group  
Категория: Автоматические ворота

The radio frequency of the remote controls is fixed and tuned at the factory; adjustments are not required and should not be attempted by the end user. WARNING Keep transmitters and remote controls out of the reach of children. Do not let children play with or use the transmitter or remote controls. Unexpected door operations can cause personal injury or property damage. Do not place transmitter where the buttons can be accidentally or unintentionally activated. Features of the Quik-Code Wireles

Allstar Products Group MVP

Скачали: 0Размер: 1 mb    Производитель: Allstar Products Group  
Категория: Автоматические ворота

This action will erase any previous signal that was learned by the control board and prepare it to learn your transmitter signal. At this time have your transmitter ready to transmit. STEP 2: Press and quickly release the Learn Enable button on the Super Station. The red LED light on the rear panel of the power head unit (and the work light) will illuminate and remain on, the control board is now ready to learn the signal from your transmitter. Within a twenty second time frame, press the button

Allstar Products Group LT 50

Скачали: 0Размер: 979 kb    Производитель: Allstar Products Group  
Категория: Автоматические ворота

Disconnect the power from the opener before removing cover and cutting the jumper. MAKE SURE YOU DISCONNECT THE POWER BEFORE CUTTING THE JUMPER. THE RUN TIMER WILL NOT CHANGE IF THE JUMPER IS CUT WITH THE POWER CONNECTED. This jumper is located under operator cover on the control board, as illustrated. 110057-2 Cut and Separate IMPORTANT SAFETY INSTRUCTIONS WARNING TO REDUCE THE RISK OF SEVERE INJURY OR DEATH, READ AND FOLLOW ALL INSTRUCTIONS! • Ensure authorized personnel only operate the door.

Allstar Products Group J6500

Скачали: 1Размер: 1 mb    Производитель: Allstar Products Group  
Категория: Автоматические ворота

• ADJUST THE SENSITIVITY ADJUSTMENTS ENOUGH TO ALLOW THE DOOR TO OPERATE, BUT NOT SO FIRMLY AS TO EXERT EXCESSIVE PRESSURE ON AN OBSTRUCTION BEFORE REVERSING. • AFTER INSTALLING THE OPENER, THE DOOR SHOULD REVERSE WHEN IT CONTACTS A 1-1/2" HIGH OBJECT (A PIECE OF STANDARD 2 X 4 BOARD LAID FLAT) ON THE FLOOR. B: IMPORTANT INSTALLATION 7 WARNING SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE USED TO BALANCE YOUR GARAGE DOOR ARE UNDER EXTREME TENSION AT ALL TIMES AND CAN CAUSE SEVERE INJURY OR DEAT

Allstar Products Group J3500

Скачали: 0Размер: 1 mb    Производитель: Allstar Products Group  
Категория: Автоматические ворота

The Warning and Caution boxes throughout this manual are there to protect you and your equipment. Pay close attention to these boxes as you follow the manual. WARNING Indicates a MECHANICAL hazard of INJURY OR DEATH. Gives instructions to avoid the hazard. CAUTION Indicates a MECHANICAL hazard of DAMAGE to your gate, gate operator, or equipment. Gives instructions to avoid the hazard. Indicates an ELECTRICAL hazard of INJURY OR DEATH. Gives instructions to avoid the hazard. WARNING Indicates an





Категории