Войти:

Manitowoc Ice G-0600

Скачали: 5Размер: 121 kb    Производитель: Manitowoc Ice  
Категория: Насосное оборудование

START AND RUN COMPONENT CHANGES VARY WITH THE TYPE OF MACHINE. FOR J-SERIES MACHINES ONLY, THE RUN CAPACITOR NEEDS TO BE REPLACED WITH THE ONE INCLUDED IN THE KIT. B AND G-SERIES MACHINES NEED ALL OF THE START AND RUN COMPONENTS REPLACED WITH THE ONES INCLUDED IN THE KIT. 1. 2. 3. 4. Disconnect power to the ice machine at the electrical disconnect (moving the toggle switch to the off position will not disconnect line voltage). Remove panels (top, front, left and right sides). Recover refri

Manitowoc Ice FS2

Скачали: 6Размер: 13 kb    Производитель: Manitowoc Ice  
Категория: Насосное оборудование

Tighten 1/2” conduit nut to conduit fitting. 7. Screw start component electrical box to refrigeration platform close to compressor. 8. Wire-nut L1 (black) wire lead to wire lead #78 and L2 (white) wire lead to wire lead #77. 9. Break out bottom knockout of compressor electrical box and attach common, run, and start wire leads to compressor terminals, per new wiring diagram. 10. Peel backing off new wiring diagram and place over existing wiring diagram. Manitowoc Ice, Inc. 2110 South 26 Str

Manitowoc Ice FS1

Скачали: 8Размер: 13 kb    Производитель: Manitowoc Ice  
Категория: Насосное оборудование

CAUTION! Remove entire system charge before proceeding. a. Remove the insulation from the suction line liquid heat exchanger assembly. You will see the liquid line soldered to the suction line for approximately 15”. You must remove this soldered length. b. Remove the liquid line from the suction line. Starting at the evaporator end, use a pliers and a low flame torch to carefully separate the liquid line from the suction line. c. Reinsulate the suction line. Run the removed liquid line outsid

Manitowoc Ice FLARE NUT TXV REPLACEMENT (Z100) 7625563

Скачали: 0Размер: 9 kb    Производитель: Manitowoc Ice  
Категория: Прочая кухонная техника

Slip copper extensions into TXV and swaged ends onto existing lines and sweat into place. 7. When TXV is cool, slip rubber boot over TXV and glue seam together. 8. Evacuate and weigh in proper charge. Manitowoc Ice, Inc. 2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 8009613 Web Site - Rev. 08/24/99

Manitowoc Ice Flake QF2300

Скачали: 2Размер: 2 mb    Производитель: Manitowoc Ice  
Категория: Прочая кухонная техника

6. Remove top cover from float reservoir. QF2300 Shown Float Valve Removal 1. Place the toggle switch in the OFF position, turn off the water supply and disconnect electrical power to the ice machine. 2. Disconnect water supply line at float valve quick disconnect by depressing stainless steel lever. 3. Remove water float valve coil. 4. Depress coil and rotate 1/4 turn counterclockwise. 5. With coil wires attached, lift coil off enclosure tube. 6. QF0800/QC0700/QF2300 ONLY Rotate quarter turn fa

Manitowoc Ice Flake QF0800

Скачали: 3Размер: 2 mb    Производитель: Manitowoc Ice  
Категория: Прочая кухонная техника

A. Verify valve and schrader caps are tightened to specifications (see Step 6). PRE-FORMED INSULATION TIGHTEN VALVE CAPS TO SPECIFICATIONS SV3084 B. Place insulation over schrader valve cap and left side of valve. Position the tab between the mounting bracket and rear panel. SV3085 PLACE TAB BETWEEN VALVE BODY AND PANEL C. Fold insulation and hold against right hand side of valve while securing with electrical tape. Seal the line set insulation to the shut off valve insulation with electrical ta

Manitowoc Ice Flake QF0400

Скачали: 1Размер: 2 mb    Производитель: Manitowoc Ice  
Категория: Прочая кухонная техника

(121.9 cm.) 55.0 in. (139.7 cm.) B1400 60 in. (152.4 cm.) 55.0 in. (139.7 cm.) The bin drain is exactly in the center of the bin. Part Number 000002688 Section 2 Installation Instructions Location of Ice Machine The location selected for the ice machine must meet the following criteria. If any of these criteria are not met, select another location. • The location must be free of airborne and other contaminants. • The air temperature must be at least 45°F (7°C), but must not exceed 110°F (43.4°C)

Manitowoc Ice FEMALE COUPLING KIT K00129

Скачали: 0Размер: 14 kb    Производитель: Manitowoc Ice  
Категория: Прочая кухонная техника

Field piping instructions: 1. Refer to the ice machine installation instructions for proper line routing and sizing. 2. After lines have been run, braze the four couplings (included in the kit) onto the ends of the field-installed lines. 3. Install the access fitting cores. 4. Pressurize the lines with dry nitrogen and leak check all brazed joints and core valves. 5. Evacuate line sets to 250 micron vacuum for one half-hour. A standing vacuum test should be performed now, as a final leak te

Manitowoc Ice FA290

Скачали: 3Размер: 23 kb    Производитель: Manitowoc Ice  
Категория: Прочая кухонная техника

Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Web Site - 8010213 Rev. 08/20/03 1

Manitowoc Ice F-STYLE OR NON MANITOWOC BIN 7601223

Скачали: 0Размер: 130 kb    Производитель: Manitowoc Ice  
Категория: Прочая кухонная техника

Box 1720, Manitowoc, WI 54221-1720 USA 8006823 Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Sheet 1 of 3 Web Site - 03/25/02 Q-DUAL INSTALL DATA Figure 1 8006823 Sheet 2 of 3 03/25/02 WATER INLET BRACKET Figure 2 WATER PUMP SUPPLY POSITION AFTER ROTATING PUMP HOUSING Figure 3 (Top View) 8006823 Sheet 3 of 3 03/25/02





Категории