Войти:

Jonsered ECS-4000

Скачали: 0Размер: 2 mb    Производитель: Jonsered  
Категория: Бензо и электропилы

of returns is no. of returns from the position where the adjusting has been turned clockwise and lightly seated. (Fig.20) 1. Turn the IDLE adjusting screw in such a degree that the chain does not start turning. (As the screw is turned clockwise, the idel speed increases and, vice versa.) 2. Slowly turn the L adjusting screw clockwise or counterclockwise to find a position where the maximum engine speed can be obtained. Then turn the screw counterclockwise 1/8 to 1/4 turn. 3. Turn the IDLE adj

Jonsered ECS-370

Скачали: 2Размер: 606 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

Jonsered ECS-356

Скачали: 0Размер: 451 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

NUT 5 4 N F098201- 5-027 258-32050-200 SAFETY SPRING 1 N F098201- 5-029 121-32350-200 CHAIN BAR CLAMP NUT 2 5-030 251-32350-200 SAFETY DAHPER COLLAR 1 5-031 994-31030-101 SCREV 3X10 1 N F098201- 5-032.1 258-04015-202 STOP BUTTON 1 -F098200 5-032 258-11600-200 BUTTON STOP 1 H F098201- 5-033,1 925-32350-200 ON-OFF MARX 1 -F098200 5-033 925-32600-200 STOP BUTTON MARK 1 N F098201- 5-034,1 178-01800-803 STOP CORD COMP. 1 R -C189752 5-034,1 178-01800-804 STOP CORD COMP. 1 -F

Jonsered ECS-351

Скачали: 1Размер: 456 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

Q=Quan. used C=lnterchangeability S=Stocking code: A-Fast moving B=Med. fast C=Med. move D=Slow move E=N.L.A. F=Superceded or replaced by a new part FIG.6 HANDLE FIGURE 6 ECS-351 PARTS LISTING REF. PART NO. PART DESCRIPTION Q C S SERIAL NO REMARKS 9 992-00050-011 WASHER,SMALL,5 2 c 10 992-10050-012 WASHER,S,5 2 A 11 990-51050-253 BOLT,HEX,5X25 2 B 12 992-10050-012 WASHER,S,5 2 A 13 990-11050-121 SCREW,5X12 2 A 14 219-32350-804 DAMPER,FRONT 1 c 15-1 209-32371-800 HA

Jonsered ECS-3500B

Скачали: 1Размер: 281 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

Jonsered ECS-3500

Скачали: 1Размер: 2 mb    Производитель: Jonsered  
Категория: Бензо и электропилы

Pulite oppure sostituite lo schermo antiscintilla (se fornito sulla vostra macchina). (la Figura no.18) 5. Candela Utilizzate cándele de NGK BPM-6A o equivalente. Regolate l'apertura degli elettrodi a 0.6mm. Nel caso gli elettrodi siano sporchi, puliteli con solventi o una spazzola in ferro. 6. In caso di una messa in deposito per un lungo periodo Scaricare tutto il carburante dal serbatoio del carburante, dal carburatore e dai condotti del carburante. Riparare ogni danno risultando dall'uso

Jonsered ECS-3351/B

Скачали: 0Размер: 843 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

Jonsered ECS-3351

Скачали: 0Размер: 619 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

• Stop engine before removing fuel cap. • Empty the fuel tank before storing the unit/machine. It is recommended that the fuel be emptied after each use. If fuel is left in the tank, store so fuel will not leak. • Store unit/machine and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. WARNING! Anti-vibration systems do not guarantee that you will not sustain white-finger disease or carpel tunnel syndrome. Therefore,

Jonsered ECS-3301/B

Скачали: 0Размер: 542 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

Jonsered ECS-3301

Скачали: 0Размер: 619 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

Make sure that the fuel is well mixed by shaking the container, before fueling. 5 custsvc@tanaka-ism.com Owner.s ManualECS-3301/3351 ECS-3301/3351 CHAIN OIL (Fig. 2-1 B) Fill the chain oil reservoir (2). Always use good quality chain oil. When the engine is running, the chain oil is automatically discharged. NOTE! When pouring fuel (1) or chain oil (2) into the tank, place the unit with cap side up. (Fig. 2-1B) (2) ADJUSTMENT OF CHAIN OIL SUPPLY The chain oil quantity discharged through the lubr





Категории