Войти:

Jonsered FC 2255W

Скачали: 9Размер: 2 mb    Производитель: Jonsered  
Категория: Садовые инструменты

Low speed jet L Try to find the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise.When the highest speed has been found, turn the low speed needle L 1/ 4 turn counter-clockwise. CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops. 26 – English MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment scr

Jonsered FC 2255

Скачали: 7Размер: 2 mb    Производитель: Jonsered  
Категория: Садовые инструменты

NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. FC2255, FC2255W, BC2255 Approved accessories Type Cutting attachment guard, Art. no. Centre hole in blades/cutters, O 25,4 mm Output shaft thread M12 Grass blade/grass cutter Multi 275-4 (O 275 4 teeth) 544 16 03-01 Multi 300-3 (O 300 3 teeth) 544 16 03-01 Multi 350-3 (O 350 3 teeth) 544 16 03-01 Saw blade Ma

Jonsered FC 2145S

Скачали: 2Размер: 2 mb    Производитель: Jonsered  
Категория: Садовые инструменты

Contact can result in burns to the skin. Remember the risk of fire! ! WARNING! The inside of the muffler contain chemicals that may be carcinogenic. Avoid contact with these elements in the event of a damaged muffler. ! WARNING! Bear in mind that: Engine exhaust fumes contain carbon monoxide, which can cause carbon monoxide poisoning. For this reason you should not start or run the machine indoors, or anywhere that is poorly ventilated. The exhaust fumes from the engine are hot and may contain s

Jonsered FC 2145

Скачали: 9Размер: 2 mb    Производитель: Jonsered  
Категория: Садовые инструменты

Oiling the air filter Always use special filter oil. Filter oil contains a solvent to make it spread evenly through the filter.You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never use common engine oil. This would drain through the filter quite quickly and collect i

Jonsered ECV-5601

Скачали: 0Размер: 242 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

Jonsered ECV-4501

Скачали: 0Размер: 618 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

If the cutting attachment still rotates after idle speed adjustment, contact your service workshop. NOTE! The L and H screws should only be adjusted by an Authorized Tanaka Dealer. The standard openings (returns) of L/H screws from lightly seated positions are as follows: WARNING! When the engine is idling the cutting attachment must under no circumstances rotate. NOTE FOR THE US MARKET!! (Fig. 3-1B) We would like to inform that the machines, which carry the following label on the unit are diffe

Jonsered ECS-650/655

Скачали: 2Размер: 498 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

Q=Quan. used C=lnterchangeability S=Stocking code: A-Fast moving B=Med. fast C=Med. move D=SJow move E=N.L.A. F=Superceded or replaced by a new part FIGURE 2 cont. ECS-655 PARTS LISTING REF. PART NO. PART DESCRIPTION Q C S SERIAL NO REMARKS 44 990-11030-061 SCREW.3X6 2 D 51 992-10050-012 WASHER, S,5 2 A 52 992-10050-062 WASHER,S,5 2 D 53 992-00050-061 WASHER,SMALL,5 3 D * Indicates the part is included in a kit or assembly and is not availiable individually. Q=Quan. used C=

Jonsered ECS-506

Скачали: 0Размер: 381 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

Jonsered ECS-415

Скачали: 0Размер: 406 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

Jonsered ECS-4000/B

Скачали: 0Размер: 308 kb    Производитель: Jonsered  
Категория: Бензо и электропилы

Q=Quan. used Olnterchangeability S=Stocking code: A-Fast moving B=Med. fast C=Med. move D=Slow move E=N.L.A. F=Superceded or replaced by a new part FIGURE 5 cont. ECS-4000/B PARTS LISTING REF. PART NO. PART DESCRIPTION Q C S SERIAL NO. REMARKS 53 990-51050-253 BOLT,HEX,5X25 1 B 54 525-32530-900 CAP,OIL ASS'Y 1 D 55 999-67020-000 O-RING,P20 1 C 60 002-32810-800 BASE.ENGINE 1 D 61 219-32600-821 DAMPER,FRONT 2 C 62 266-32530-801 DAMPER.B 1 D 63 209-32810-80 HANDLE,FRONT





Категории