Войти:

Powermatic WP2510

Скачали: 23Размер: 4 mb    Производитель: Powermatic  
Категория: Рубанки

Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the planer is installed and running properly. Compare the contents of your container with the following parts list to make sure all parts are intact. Missing parts, if any, should be reported to your distributor. Read the instruction manual thoroughly for assembly, maintenance and safety instructions. NOTE: To remove the box from atop the planer table, loosen the table lock handle,

Powermatic 60B

Скачали: 1Размер: 3 mb    Производитель: Powermatic  
Категория: Кромочные фрезеры

Proceed as follows: 6. Rotate the cutterhead (using the pulley) until the tip of the knife is at the top of the cutterhead arc. Place the knife setting gauge (Figure 17) over the cutterhead so the tip of the knife contacts the center of the gauge, and all four "feet" of the gauge rest firmly upon the cutterhead, as the knife is pushed down into its slot. The gauge will set the knives at approximately .070" above the cutterhead. Knife height should not vary more than .002-.003" across the length

Powermatic WP2412

Скачали: 5Размер: 3 mb    Производитель: Powermatic  
Категория: Беспроводные гарнитуры и прочие аксессуары

1....................................................................................................................19 Drawing No. 1 ....................................................................................................................................21 Parts List: Drawing No. 2....................................................................................................................22 Drawing No. 2 .........................................................................

Powermatic 60C

Скачали: 2Размер: 3 mb    Производитель: Powermatic  
Категория: Кромочные фрезеры

1 55............. 6296062...................Bolt........................................................................................................ 1 56............. 6296063...................Collar .................................................................................................... 1 57.............TS-0680031.............Flat Washer........................................................5/16”...........................6 59............. 6296167...................Depth Scale.

Powermatic 60HH

Скачали: 0Размер: 3 mb    Производитель: Powermatic  
Категория: Кромочные фрезеры

Then rotate the key so that the arrow lines up with the LOCK arrow on the cover. This will prevent the safety key from coming loose from vibration when the machine is in use. Figure 30 21 Basic Jointer Operation NOTE: If you are inexperienced at jointing, use scrap pieces of lumber to check settings and get the feel of operations before attempting regular work. This section briefly discusses general rules as well as some of the basic cuts using a jointer, such as surfacing, edging, beveling, ske

Powermatic 201

Скачали: 1Размер: 3 mb    Производитель: Powermatic  
Категория: Рубанки

2 42 6012165 Key, 8 x 7 x 30 .................................................................................................... 1 43 6012166 Infeed Shaft ........................................................................................................ 1 44 6012167 Infeed Roller...................................................................................................... 22 45 6012168 Shaft ..........................................................................................

Powermatic Single End Dovetailer DT45

Скачали: 17Размер: 3 mb    Производитель: Powermatic  
Категория: Сварочные аппараты

16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. 17. Provide for adequate space surrounding work area and non-glare, ove

Powermatic 3520B

Скачали: 15Размер: 2 mb    Производитель: Powermatic  
Категория: Станки

High speed can build friction while sanding and cause heat check in some woods. 2. Begin with fine sandpaper (120 grit) and progress through each grit, using only light pressure. Coarser sandpaper tends to leave deep scratches that are hard to eliminate. Use power-sanding techniques to avoid concentric sanding marks around your finished piece. Avoid rounding over the rim and foot with sandpaper; try to keep details crisp. Finish sanding with 220 grit. 3. Remove sanding dust with tack rags or com

Powermatic 209

Скачали: 4Размер: 2 mb    Производитель: Powermatic  
Категория: Рубанки

If one of our tools needs service or repair, one of our Authorized Service Center located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your POWERMATIC® tools. For the name of an Authorized Service Center in your area call 1-800-274-6848. MORE INFORMATION WMH Tool Group is consistently adding new products

Powermatic 209HH

Скачали: 8Размер: 2 mb    Производитель: Powermatic  
Категория: Рубанки

Proceed as follows: 1. Connect power, and turn on the planer. 2. Take a scrap board and measure its exact thickness with calipers. 3. Raise or lower the table so the scale reads the thickness of the board minus 1/16". Feed the board through the planer. 4. Move the table up another 1/16". Flip the board over and plane the other side. 5. Measure the board with calipers and compare with the depth scale on the planer. If the scale needs adjustment, loosen the screws and shift the scale up or down as





Категории