Войти:

Ives Door

Скачали: 6Размер: 1 mb    Производитель: Ives  
Категория: Двери и окна

Ives 780

Скачали: 14Размер: 437 kb    Производитель: Ives  
Категория: Двери и окна

780 Door Chime DWG # 2375 Rev A, new drawing # 9/7/00 Tools Required: Hand or electric drill No. 2 point Phillips screwdriver 1 inch, 3/32 inch and 7/64 inch drills STEP 1 STEP 2 STEP 3 Mark horizontal reference line on OUTSIDE of door at convenient eye level (recommended 58 inches up from bottom of door). Mark vertical line on door centered from left to right. (See fig. 1) Align template reference lines with lines on door and mark location of 3 holes labeled "OUTSIDE ©" on door. Dril

Ives AM-KP

Скачали: 0Размер: 270 kb    Производитель: Ives  
Категория: Двери и окна

CONNECT CABLE 6. SET DEVICE ADDRESS 7. SECURE & LOCK CASE AM/II f m KEYP AD IN :-f + o o o o o o © -9- 00 I I à à s s ¿> PWR | GND | DAT11 DATO | DVAL | CLK 0 AM- USE A SMALL SCREWDRIVER TO SET THE DEVICE ADDRESS SWITCH FOR LOCAL POWER, DISCONNECT RED WIRE FROM "PWR" CONNECTION ON AM-KP AND CONNECT EXTERNAL 12 VDC SUPPLY (+ TO PWR & - TO GND) NOTE: AM/II * MUST BE CONNECTED TO AM-KP "GND" 8. PROGRAM SYSTEM PROGRAM THE AM/II TO CONFIGURE THE KEYPAD(S) AND SET THE ENTRY CODES R

Ives 112HD Series

Скачали: 4Размер: 196 kb    Производитель: Ives  
Категория: Двери и окна

Not doing so may result in improper installation and void the manufacturer’s guarantee. These hinges have a permanent, factory applied lubricant. Removal or alteration of this lubricant, anodizing or painting of the product in the field will void the guarantee. INSTALLATION NOTES Reinforcing and Rivet nuts: No reinforcing is necessary except on extremely high frequency, extremely heavy or extra-wide doors. Rivet nuts are required in the frame and door when door weight exceeds 450 pounds (up t

Ives 224HD Series

Скачали: 7Размер: 196 kb    Производитель: Ives  
Категория: Двери и окна

.. .... Ingersoll Rand © 2006 Ingersoll-Rand Company Limited Security Technologies 829168-00 INSTALLATION Q Mark frame hole locations. A. Open hinge and place frame leaf flat against surface of frame leaving 1/8” gap between top of hinge and frame header. Hinge lip should be held tight against the frame face from top to bottom. B. Mark all hole locations on frame using center punch provided. C. Drill all holes using #13 (.185”) or 3/16” (.188”) drill for metal frame. For wood frame us

Ives 926

Скачали: 0Размер: 94 kb    Производитель: Ives  
Категория: Двери и окна

Position jamb bracket 1/4" in from door and fasten to doorframe (see illustration below) .Open side of bracket must be facing screen or storm — 2. Slide the "hold open" washer onto rod. Use short connecting pin to connect closer to jamb bracket. The “hold open" washer should be placed over lugs against closer tube (see illustration below). This will provide proper tension for installation and should not be adjusted until installation is complete. 3. Use long connecting pin to attach door brack

Ives 711 Series

Скачали: 0Размер: 88 kb    Производитель: Ives  
Категория: Качели

Ives 611 Series

Скачали: 9Размер: 88 kb    Производитель: Ives  
Категория: Качели

Ives 620 Series

Скачали: 4Размер: 85 kb    Производитель: Ives  
Категория: Двери и окна

Ives 702 Series

Скачали: 5Размер: 85 kb    Производитель: Ives  
Категория: Двери и окна





Категории